Model reference
Whirlpool CHW8990CW0
Washer
4 documents21 error codes18 service modes
Available documentation
Tech Sheet
- Laveuse Commerciale À Chargement Frontal, ModÈle CHW8990C Ou Version UltÉrieure – OpÉrations De Base16 pg
- techsheet-w10311069-revb16 pg
- Tech Sheet - W10702904 - Rev C16 pg
Installation Guide
- Installation Instructions32 pg
MyPros+ Max
Diagnose your Whirlpool CHW8990CW0.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (21)
CodeMeaning
d13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorF01CCU errorF11Motor Control Unit (MCU) has a failure, possibly a repeating under or…F20No water detected entering washerF21Long drainF22Door lock errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionsF28Communication failure between CCU and MCU.F29Door unlock errorF31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F70Communication failure between CCU and User Interface (UI).F73UI failureF74UI failureService modes (18)
- Code Display Mode["Can only be accessed when the washer is in error state.","Open the service door.","The current F…
- Credit a Cycle["Enter diagnostic blink mode (display flashing).","Press the HOT button to credit a cycle (display…
- Cycle Credit["Enter Flashing Mode (diagnostic mode with display flashing).","Press the HOT button (CC will…
- Diagnostic Mode (Washer Diagnostic Mode)["Open the service door.","Press the 'Start Operating Set-up' button to enter setup mode.","Press…
- Help Mode["Open the service door.","For manual communication
- Help Mode (DA Communication Established)["Open the service door.","The message dAS will appear in the display.","Press the HOT…
- Help Mode (Manual Communication)["Open the service door.","Press the WARM button until the set-up code 2.XX is on display.","Press…
- Manual Overview Test["Enter Flashing Mode (diagnostic mode with display flashing).","Press the COTTON/WHITES button to…
- Manual Overview Test (Full Diagnostic Test)["Enter diagnostic blink mode (display flashing).","Press the COTTON/WHITES button."]
- Quick Overview Test["Enter Flashing Mode (diagnostic mode with display flashing).","Press the WARM button to start the…
- Quick Overview Test (Rapid Diagnostic Test)["Enter diagnostic blink mode (display flashing).","Press the WARM button."]
- Quick Spin Cycle["Enter Flashing Mode (diagnostic mode with display flashing).","Press the PERM PRESS button to…
- Set-Up Mode (Manual Communication / Coin Payment)["Insert service access door key, turn, and lift to remove service access door.","The washer enters…
- Setup Mode["Insert access door key, turn, and lift to remove access door.","Use HOT button to adjust values…
- Setup Mode (Operating Setup)["Coin-operated models
- Washer Clean Cycle (Diagnostic)["Enter diagnostic blink mode (display flashing).","Press the COLORS/DELICATES button."]
- Washer Cleanout Cycle["Enter Flashing Mode (diagnostic mode with display flashing).","Press the COLORS/DELICATES button…
- Washer Diagnostic Mode (Flashing Mode)["Enter Set-Up Mode first (open service door).","Press and hold the COLD button for 2 seconds while…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool washer models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax