Model reference

Bosch SHX68T55UC/02

Name: Bosch SHX68T55UC/02
Brand: Bosch

Dishwasher

3 documents24 error codes3 service modes

Available documentation

Tech Sheet

Fault Codes and Service Programs5 pg
Covers this model

Service Manual

Repair Instruction - Dishwasher 800 Series Service Manual137 pg
Covers this model
Bosch Dishwasher Service Manual64 pg
Covers this model

MyPros+ Max

Diagnose your Bosch SHX68T55UC/02.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Bosch Dishwasher

E:01 on my Bosch SHX68T55UC/02

M+

Wash cycle completed prematurely;

From Service Manual 318737, p.29:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure drain pump winding resistance at connector J7. Expected: 12 to 16 ohms at room temperature.

3.Verify the board switches the pump at 120 VAC during the drain cycle.

Part 00620774

Drain pump

Error codes (24)

CodeMeaning

E:01Wash cycle completed prematurely; Sanitized LED flashes E:02Dishwasher runs without heating; Sanitized LED flashes E:04Sanitized LED flashes; caused by faulty safety heater relay.E:05Water switch runs continually; Sanitized LED flashes; dishwasher will drain and…E:06Wash cycle abruptly stops; Sanitized LED flashes E:08Heat pump detects low water level; error code won't show during wash cycle.E:09Sanitized LED flashes; caused by faulty heater circuit (open-circuited).E:11Sanitized LED flashes; caused by heat pump NTC resistances out of range or NTCs…E:13Error code won't show during wash cycle; incoming water too hot (> 75°C /…E:15Wash cycle abruptly stops, dishwasher drains intermittently, Sanitized LED…E:17Wash cycle abruptly stops, dishwasher drains continually, Sanitized LED flashes E:18Dishwasher waits for water filling, then wash cycle abruptly stops, Sanitized…E:20Sanitized LED flashes; caused by heat pump blocked/clogged, water in sump, or…E:21Sanitized LED flashes; caused by faulty heat pump wire harness or faulty heat…E:22Sanitized LED is lit; caused by inlet water flow rate too high.E:23Sanitized LED flashes; caused by inlet water flow rate too low.E:24Wash cycle completed prematurely, dishwasher won't drain, Sanitized LED is lit E:25Wash cycle completed prematurely, dishwasher won't drain, Sanitized LED is lit E:26Error code won't show during wash cycle; caused by faulty water switch harness…E:27Sanitized LED is lit; caused by low supply voltage (< 98 VAC).E:28Aqua sensor doesn't run during wash cycle; error code won't show during wash…E:29Wash cycle abruptly stops or dishwasher won't run, or dishwasher doesn't…E:30Dishwasher shuts off; error code won't show during wash cycle E:32Error code won't show during wash cycle. Caused by overloaded drain pump

Service modes (3)

Customer settings modeWith the appliance switched on, simultaneously press button A and the 'Start' button.
Electronic button lock (childproof lock)Start the required programme, then hold down button B for approx
Error Code Program (P0)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Bosch dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass