mypros+
Model reference

Bosch SHX88

Dishwasher

3 documents41 error codes4 service modes

Available documentation

Service Manual

  • Repair manual - Dishwasher200 pg
    Covers this model
  • Repair Instruction - Dishwasher 800 Series Service Manual137 pg
    Covers this model

Wiring Diagram

  • Wiring Diagram2 pg
    Covers this model
MyPros+ Max

Diagnose your Bosch SHX88.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (41)

CodeMeaning
1077Home Connect app cannot pair with or find dishwasher on customer home network.1080Phone couldn't connect to Wi-Fi network automatically; occurs with iPhones when…1081Pairing will time out; usually occurs with Android Oreo (8.0+), customer device…1086Device connected to wrong network (SSID) or not connected to network (e.g3404Dishwasher not coded or coded incorrectly; missing customer specific…4613Dishwasher not intended for US market; customer moved to US with overseas…4623Customer has been logged out; pairing attempted after logout.5014Customer firewall or anti-virus software is blocking access during pairing…7101Replacement power module not coded; occurs after power module was replaced.E:01Faulty relay to heat pump heater, or heat/drain pump disconnected or faulty.E:02Ground fault at heat pump heater or zeolite heater, faulty heater relay, or low…E:03Overheated power module / power cord connection detected by on-board PTC.E:04Faulty safety heater relay on power module, or ground fault at heat pump heater…E:05Faulty water switch relay on power module; dishwasher drains and finishes…E:06Door ajar, not properly latched, popped open, or faulty/misaligned door latch…E:07Zeolite fan faulty or blocked.E:08Heat pump detects low water level; will not show during wash cycle.E:09Faulty heater circuit (open-circuited).E:10Faulty or blocked zeolite fan, or faulty/loose zeolite heater harness.E:11Heat pump NTC resistances out of range.E:12Heat pump heater calcified; dishwasher runs without heating.E:13Water heater turned up too high (>75°C / 167°F); will not show during wash…E:14Faulty flow meter; dishwasher switches to time filling, water flow detected by…E:15Water in base activated float switch; dishwasher abruptly stops and can't be…E:16Flow meter senses water flow with closed inlet valve; faulty water inlet valve.E:17Inlet water flow rate/pressure too high; flow meter measures excessive water…E:18Inlet water flow rate/pressure too low; heat pump measures insufficient water…E:19Loose/faulty harness to detergent actuator or faulty dispenser actuator.E:20Faulty heat pump motor winding, pumps disconnected, or faulty harnesses; wash…E:21Heat pump is blocked/clogged.
View all 41 error codes

Service modes (4)

  • CS Program Mode (Error Code Viewing / CS Test Program / Component Test)["Ensure dishwasher has been reset and turned off.","While pressing and holding buttons 'B' and…
  • Customer Settings (Codings) Mode["Turn dishwasher off with no wash programs running.","Open the door.","Press 'On/Off' button to…
  • Customer settings modeWith the appliance switched on, simultaneously press button A and the 'Start' button.
  • Electronic button lock (childproof lock)Start the required programme, then hold down button B for approx

Full entry steps, exit procedures, and test sequences are available in Max.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass