mypros+
Model reference

Maytag W10311070

Washer

1 document21 error codes11 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10311070 - Rev B (FR)16 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag W10311070.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (21)

CodeMeaning
d13Coin 2 sensor error; the coin 2 detector detects the coin slot is obstructed…d16Generation 2 debit card reader error; no communication from the debit card…d5Coin 1 sensor error; the coin 1 detector detects the coin slot is obstructed…d9Low voltage detection error; input voltage detected below 90 VAC for 8 seconds.F01MCC (Central Control Module) communication error; the pump drive in the MCC…F11Motor Control Module (MCM) failure, possibly due to repeated under-voltage or…F20No water detected entering the washer; the first pressure switch threshold is…F21Excessive drain time; the drain operation exceeds eight minutes without…F22Door lock error; the washer made multiple attempts to lock the door and failedF24Water temperature sensor error; the sensor value is out of range (-5°C to 103°C…F25Tachometer error; the MCC cannot correctly detect the motor speed, causing the…F26Door switch error; the door switch circuit remains open for 5 seconds while the…F27Overflow condition; the overflow contact of the pressure switch is closed for…F28Communication failure between MCC (Central Control Module) and MCM (Motor…F29Motor overheated; the MCM detects the motor drive has overheated.F31MCM serial communication error between the MCC and MCM.F33Pump disconnected; the electrical connection between the pump and the MCC is…F34Load detected in washer during the washer clean cycle; the washer detects a…F70Communication failure between MCC (Central Control Module) and UI (User…F73UI (User Interface) failure; communication error in the User Interface…F74UI (User Interface) failure; communication error in the User Interface…

Service modes (11)

  • Diagnostic Mode (Blink Mode)["First access Setup mode (see Setup/Configuration Mode entry).","Press QUICK CYCLE button for 1…
  • Free Cycle Credit["Enter Blink Mode (entire display is blinking).","Press the PERM
  • Help Mode (dAS mode)["Open the service door or insert a manual diagnostic card.","dAS message appears on the…
  • Help Mode (PD models)["Open the service door.","Press DELICATES AND KNITS until display shows 2.XX.","Press PERM
  • Manual Overview Test Program["Enter Blink Mode (entire display is blinking).","Press the WHITES button."]
  • Quick Drain and Spin Program["Enter Blink Mode (entire display is blinking).","Press the COLORS button."]
  • Quick Overview Test Program["Enter Blink Mode (entire display is blinking).","Press the DELICATES AND KNITS button."]
  • Service Access Code (PR models configured as PN without key switch)["Using only the three bottom buttons (numbered 1, 2, 3 from left to right):","1. Press button 2…
  • Setup/Configuration Mode (PD models)["Insert key into service door access.","Turn and lift to remove the service access door.","Use the…
  • Setup/Configuration Mode (PR models via AA1 connector)["Unplug the washer or disconnect power.","Open the console and disconnect connector AA1.","Close…
  • Washer Clean Cycle["Enter Blink Mode (entire display is blinking).","Press the BRIGHTS button."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass