mypros+
Model reference

Samsung WF326

Washer

6 documents22 error codes23 service modes

Available documentation

Service Manual

  • LG Samsung WF306BHWXAA Service Manual Product Specification4 pg
    Covers this model
  • Samsung Front Load Washer88 pg
    Covers this model
  • Samsung Washer Test Modes Special Test Mode (SERVICE MODE)1 pg
    Covers this model
  • Samsung Washer Test Modes1 pg
    Covers this model
  • Washing Machine Service Manual104 pg
    Covers this model

Tech Sheet

  • Washer Connector Checks1 pg
    Covers this model
MyPros+ Max

Diagnose your Samsung WF326.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (22)

CodeMeaning
2EVoltage for motor control bus is over or under specified limit.3EOver-current is detected7ESilver Care Kit (Silver Care PCB) Failure.8EMEMS Sensor FailurebEMotor hall sensor signals come out without motor operation.dcUnbalance or cabinet bump detected during final spin, preventing drum from…dLDoor is detected as open when the motor is operating.dSDoor is detected as open while it is trying to lock the door.E2Jammed KeyE3MICOM is attempting to drive the motor but is not getting any response signals…EEEEModel option Error displayed during Quick Test Mode (Need to replace PCB Assy).FLDoor fails to lock after 3 attempts.HrHeater Relay Failure (No Heater Relay Check Signal).LEWater Level Sensor TroubleLODoor fails to unlock after 3 attempts.ndThe water level fails to drop below the Reset Water Level within 15 minutes.nFFilling continues for more than 16 minutes or there is no change of water level…OEWater level sensor data (frequency) shows water level is at or above the…PFPower failure occurred during washingSrSystem Relay (Main Relay) FailureSUdSSuds detected during washing sessiontEAbnormal high/low temperature or resistance (Thermal sensor or PBA) resistance.

Service modes (23)

  • Board Input TestEnter Service Mode, then press EXTRA WASH. Turn Selector Knob counter-clockwise to access…
  • Board Input Test ModeDuring Special Test Mode, press the Extra Wash Key.
  • Continuous Run Mode1
  • Cycle CountEnter Service Mode, then press SIGNAL button.
  • Cycle Count Check ModeDuring Special Test Mode, press the Signal Key.
  • Diagnostic Code Check ModeDuring Special Test Mode, press the Silver Wash (Rinse Water +) Key
  • EEPROM Reset Mode1
  • EEPROM Test and Reset ModePower OFF, press Temp Key, Spin Key and Power Key at the same time.
  • Fast Time DownEnter Service Mode, then press TEMP button.
  • Fast Time Down Test ModeDuring Special Test Mode, press the Temp Key.
  • Fault Code TestEnter Service Mode, then press SPIN (WF203, WF206, WF218), or SilverCare (WF306, WF316, WF317…
  • Quick Spin TestEnter Service Mode, then press Delay Start & Spin (WF203, WF206, WF218), or Delay Start & Silver…
  • Quick Spin Test ModeDuring Special Test Mode, press Delay Start and Silver Wash Keys (Rinse Water + Key) for 3 seconds.
  • Quick Test Mode1
  • Quick Test Mode - Door Lock/Unlock TestWhile in Quick Test Mode
  • Quick Test Mode - Heater TestWhile in Quick Test Mode
  • Quick Test Mode - Motor TestWhile in Quick Test Mode, press the Spin button to activate Motor test (WF203, WF206, WF218, WF306…
  • Quick Test Mode - Pump TestWhile in Quick Test Mode
  • Quick Test Mode - Water Valve TestWhile in Quick Test Mode, press the Temp button to activate Water Valves test
  • S/W Version Check ModeDuring Special Test Mode, press the Soil Level Key.
  • Software NumberEnter Service Mode, then press SOIL button.
  • Special Test Mode1
  • Special Test Mode (Service Mode)Power ON, then press and hold SIGNAL and EXTRA RINSE buttons simultaneously for 3 seconds.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Samsung washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass