mypros+
Model reference

Whirlpool GS563LXSQ0

Range

13 documents27 error codes10 service modes

Available documentation

Tech Sheet

  • TECH SHEET8 pg
    Covers this model
  • Tech Sheet - W10041630 - Rev A (FR)8 pg
    Covers this model
  • TECH SHEET - GS563LXSS1 WP Range8 pg
    Covers this model
  • FICHE TECHNIQUE - Tech Sheet W10041630 Rev A8 pg
    Covers this model
  • TECH SHEET - Whirlpool Gas Range GS563LXSS06 pg
    Covers this model

Service Manual

  • GAS RANGE Use & Care Guide44 pg
    Covers this model
  • Whirlpool Gas Range Direct Spark Ignition System29 pg
    Covers this model
  • Job Aid - 30″ Freestanding Self-Cleaning Gas Range68 pg
    Covers this model
  • 30″ Freestanding Self-Cleaning Gas Range68 pg
    Covers this model
  • Whirlpool Gas Range Direct Spark Ignition System KR-2829 pg
    Covers this model

Installation Guide

  • Instruction Sheet1 pg
    Covers this model
  • Installation Instructions32 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool GS563LXSQ0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (27)

CodeMeaning
E0EEPROM communication failure, possibly caused by power line noise or lightning.E1EEPROM checksum failure, possibly caused by power line noise or lightning.E2Short circuit in oven sensor circuitE3Door latch malfunctionF0 E0Factory defaultF1 E0EEPROM communications failure, possibly caused by power line noise or lightning.F1 E1EEPROM checksum failure, possibly caused by power line noise or lightning.F1 E2UL A/D error(s).F1 E3Fuel type (gas/electric) select failureF1 E4Model ID error.F1 E6Latch signal mismatch error.F2 E0Key contact closed for more than 60 secondsF2 E1No communication between keyboard and controlF2 E6STOP/CLEAR key contact closed for more than 60 secondsF3 E0Break in oven sensor circuitF3 E1Short in oven sensor circuitF3 E2BAKE/BROIL temperature out of range (too high)F3 E3Clean temperature out of range (too high)F3 E4Oven sensor openedF3 E5Oven sensor shortedF3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F5 E0Door switch open during cleanF5 E1Door latch not operatingF8 E0N/A (no likely failure condition described).GoodNo failure present; displays only if user enters diagnostic mode and there are…PFA reset has occurred in the Electronic Range Control (ERC), typically caused by…

Service modes (10)

  • Last Error Code RecallPress and hold the CANCEL/OFF key for 5 seconds until the last error code is displayed.
  • Manual Diagnostic Mode 1Enter within 120 seconds of power-up
  • Manual Diagnostic Mode 2Enter more than 120 seconds after power-up
  • Manual Diagnostics Mode 1Within 120 seconds of power-up, press Cancel/OFF, Cancel/OFF, then Start key
  • Manual Diagnostics Mode 1 (Full - within 120 seconds of power-up)Within 120 seconds of power-up, press Cancel/OFF, Cancel/OFF, then START
  • Manual Diagnostics Mode 2After 120 seconds of power-up, press Cancel/OFF, Cancel/OFF, then Start key.
  • Manual Diagnostics Mode 2 (Limited - after 120 seconds of power-up)After 120 seconds of power-up, press Cancel/OFF, Cancel/OFF, then START
  • Temperature Adjustment (BAKE offset)Press and hold BAKE pad for 5 seconds. Current offset is shown in 3-digit display (CAL is shown in…
  • Temperature Adjustment (Calibration)Press and hold BAKE pad for 5 seconds. Current offset is shown in 3-digit display. CAL is shown in…
  • Temperature Calibration (Touchpad control module)Press and hold BAKE for 5 seconds

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass