Model reference
Whirlpool GW395LEP
Range
4 documents41 error codes17 service modes
Available documentation
Service Manual
- Self-cleaning Slide-in Gas Range KR-35 Job Aid68 pg
- TECHNICAL EDUCATION JOB AID 4317368 KAC-40 FAILURE CODES AND WIRING DIAGRAMS for WHIRLPOOL AND KITCHENAID SLIDE-IN & FREESTANDING GAS & ELECTRIC RANGES80 pg
Service Flash
- Service Pointer - 8178519 (Gas Oven Will Not Reignite During Cooking Cycles)2 pg
- Service Pointer - 8178664 - Control Not Responding2 pg
MyPros+ Max
Diagnose your Whirlpool GW395LEP.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (41)
CodeMeaning
E0Shorted oven temperature sensor circuit.E1Open oven temperature sensor circuit or Electronic Oven Control (EOC) failure.E2Oven temperature is too high (exceeded maximum threshold).E3Open oven temperature sensor or Electronic Oven Control failure.E5Door latch failureE6Door latch failureF0 E0No failure (default state).F1Electronic Oven Control (EOC) internal failure.F1 E0EEPROM communication error (Tulsa/Celaya); Internal error (Oxford).F1 E1EEPROM checksum error (Tulsa/Celaya); Internal error (Oxford).F1 E2UL A/D error (Tulsa/Celaya); Internal error (Oxford).F1 E3Internal error (Oxford).F1 E4Model ID error (Tulsa/Celaya); Internal error (Oxford).F1 E5Internal error (Oxford)F1 E6Latch signal mismatch error (Tulsa/Celaya); Internal error (Oxford)F1 E7Internal error (Oxford)F1 E8Internal error (Oxford)F1 E9Internal error (Oxford)F2 E0Shorted keypad / stuck key.F2 E1Keypad disconnect / keypad disconnected.F3 E0Top oven sensor open (main sensor open).F3 E1Top oven sensor shorted (main sensor shorted).F3 E2Meat probe shorted (Tulsa/CelayaF3 E3BAKE range over temperature (Tulsa/Celaya); Bottom oven sensor shorted is F3 E3…F3 E4Bottom oven sensor open (Oxford); CLEAN range over temperature (Tulsa/Celaya).F3 E5Lower oven sensor shorted (bottom sensor short).F3 E6Warming drawer sensor open (WD sensor open).F3 E7Warming drawer sensor shorted (WD sensor shorted).F4 E2Over temperature during cook cycle (temperature runaway error).F4 E3Over temperature during clean cycle (temperature runaway error).View all 41 error codes
F4 E7Over temperature cavity 2 (temperature runaway error in second cavity).F5Door lock error during Clean (3-digit display / knob control).F5 E0Door and latch switches do not agree (door latch mismatch).F5 E1Latch or latch switch failure / no operating latch / latch not operating.F5 E2Door switch fault.F5 E4Latch switch fault.F5 E6Centertap voltage failure (Tulsa/Celaya).F5 E7Unlock door error / cannot unlock door.F6 E4Lost communication between power board and display board.F6 E5Cancel key error.PFPower failure (not a failure mode, informational only).
Service modes (17)
- Disable/Enable Cycle End Audible Signals (Hidden Function)Press and hold the COOK TIME keypad for 5 seconds.
- Disable/Enable Timer Reminder Signals (Hidden Function)Press and hold the TIMER SET keypad for 5 seconds.
- Disable/Enable Valid Data Entry Signals (Hidden Function)Press and hold the STOP TIME keypad for 5 seconds.
- Keyboard LockoutPress and hold the START key for 5 seconds to disable/enable all oven functions (Bake, Broil, Clean)
- KitchenAid EZ373 & 520 Test ModeAvailable for first 60 seconds after power up. Press
- KitchenAid GOC Clock Manual DiagnosticsWithin 120 seconds of power up
- Manufacturing Test Mode (EZ354)Available for only the first 60 seconds after power up
- Oxford GOC Clock Manual DiagnosticsWithin 120 seconds of power up
- Recall Last Failure CodePress and hold the OFF/CANCEL key for 5 seconds.
- Software Revision Number (Hidden Function)Press and hold the START/ENTER keypad for 5 seconds.
- Temperature Calibration Offset (Hidden Function)Press and hold the BAKE keypad for 5 seconds
- Temperature Scale Selection (Hidden Function)Press and hold the BROIL keypad for 5 seconds to toggle between °F and °C.
- Whirlpool EZ175 & 176 Self-Diagnostic Test ModeAvailable for first 60 seconds after power up. 1) Simultaneously press BAKE and CLOCK. 2) Display…
- Whirlpool EZ300 Self-Diagnostic Test ModeAvailable for first 60 seconds after power up. 1) Sequentially press
- Whirlpool EZ354, 357, 358, & 410 Test ModeAvailable for first 60 seconds after power up. Press
- Whirlpool EZ625 Diagnostic Test1) Disconnect power for at least 15 seconds, then reconnect. 2) Within one minute of power up, press
- Whirlpool GOC Clock Manual DiagnosticsWithin 120 seconds of power up
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass