Model reference

Whirlpool SF367LXSQ1

Range

8 documents39 error codes5 service modes

Available documentation

Tech Sheet

Tech Sheet - W10116297A (FR)6 pg
Covers this model
Tech Sheet - W10116296A6 pg
Covers this model

Service Manual

Whirlpool Gas Range Direct Spark Ignition System29 pg
Covers this model
Job Aid - 30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
Whirlpool Gas Range Direct Spark Ignition System KR-2829 pg
Covers this model

Installation Guide

Installation Instructions32 pg
Covers this model
Instruction Sheet2 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool SF367LXSQ1.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

E0 on my Whirlpool SF367LXSQ1

M+

EEPROM communications failure.

From Tech Sheet W12665363, p.15:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (39)

CodeMeaning

E0EEPROM communications failure.E0-F1EEPROM checksum failure.E0-F3Oven sensor opened.E0-F5Door and switches do not agree.E1EEPROM checksum failure.E1-F1UL A/D error(s).E1-F3Oven sensor shorted.E1-F5Door latch not operating.E2UL A/D error(s).E2-F2Shorted key detected.E2-F3BAKE/BROIL range over temperature.E2-F5Latch error during CLEAN.E3-F3CLEAN range over temperature.F0 E0Factory default F1 E0EEPROM communications error.F1 E1EEPROM checksum error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.F1-E0Keypad short circuit (stuck key).F2 E0Shorted key.F2 E1Key tail unplugged.F2-E0Oven sensor open circuit.F2-E1Oven sensor short circuit.F2-E2BAKE/BROIL excessive temperature (oven overheating during bake or broil).F2-E3CLEAN excessive temperature (oven overheating during self-clean cycle).F3Door latch does not operate properly.F3 E0Oven sensor opened F3 E1Oven sensor shorted F3 E2Bake range over temperature.

View all 39 error codes

F3 E3Clean range over temperature.F3 E4Oven sensor opened F3 E5Oven sensor shorted F3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F5 E0Door switches do not agree.F5 E1Door latch not operating.F8 E0N/A (no likely failure condition described).PFA reset has occurred in the Electronic Range Control (ERC), typically caused by…

Service modes (5)

Diagnostic ModeAccess diagnostic screen 5 (A-Last fault code / B-Cleared error code) as referenced on page 4
Diagnostics ModeWith oven not in cooking, broiling, or cleaning mode, press
Last Error Code RecallPress and hold the CANCEL/OFF key for 5 seconds until the last error code is displayed.
Temperature Adjustment ModePress and hold BAKE key for 5 seconds
Temperature Calibration / Offset AdjustmentPress and hold the BAKE button for 5 seconds

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass