Model reference
Whirlpool SF380LEPS0
Range
8 documents47 error codes13 service modes
Available documentation
Tech Sheet
- TECH SHEET - 9755996 - Rev A4 pg
- techsheet 9755996 reva4 pg
Service Manual
- TECHNICAL EDUCATION JOB AID 4317368 KAC-40 FAILURE CODES AND WIRING DIAGRAMS for WHIRLPOOL AND KITCHENAID SLIDE-IN & FREESTANDING GAS & ELECTRIC RANGES80 pg
Service Flash
- Service Pointer - 8178185 - Rev A Ignition Problems2 pg
- Service Pointer - 8178446 - PF Error Code Appears All the Time2 pg
Other
- 81781852 pg
- Service Pointer - W10622771 (Burner May Not Ignite)_W1062277118 pg
Installation Guide
- Instruction Sheet2 pg
MyPros+ Max
Diagnose your Whirlpool SF380LEPS0.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (47)
CodeMeaning
F0 E0No failure (default state).F1 E0EEPROM communication error (Tulsa/Celaya); Internal error (Oxford).F1 E1EEPROM checksum error (Tulsa/Celaya); Internal error (Oxford).F1 E2UL A/D error (Tulsa/Celaya); Internal error (Oxford).F1 E3Internal error (Oxford).F1 E4Model ID error (Tulsa/Celaya); Internal error (Oxford).F1 E5Internal error (Oxford)F1 E6Latch signal mismatch error (Tulsa/Celaya); Internal error (Oxford)F1 E7Internal error (Oxford)F1 E8Internal error (Oxford)F1 E9Internal error (Oxford)F1-E0EEPROM communications error.F1-E1EEPROM checksum failure.F2 E0Shorted keypad / stuck key.F2 E1Keypad disconnect / keypad disconnected.F2 E2UL A/D error(s).F2-E2UL A/D error(s).F3 E0Top oven sensor open (main sensor open).F3 E1Top oven sensor shorted (main sensor shorted).F3 E2Meat probe shorted (Tulsa/CelayaF3 E3BAKE range over temperature (Tulsa/Celaya); Bottom oven sensor shorted is F3 E3…F3 E4Bottom oven sensor open (Oxford); CLEAN range over temperature (Tulsa/Celaya).F3 E5Lower oven sensor shorted (bottom sensor short).F3 E6Warming drawer sensor open (WD sensor open).F3 E7Warming drawer sensor shorted (WD sensor shorted).F3-E0Shorted key / Stuck key.F3-E1Keytail unplugged.F4 E2Over temperature during cook cycle (temperature runaway error).F4 E3Over temperature during clean cycle (temperature runaway error).F4 E7Over temperature cavity 2 (temperature runaway error in second cavity).View all 47 error codes
F5Door lock error during Clean (3-digit display / knob control).F5 E0Door and latch switches do not agree (door latch mismatch).F5 E1Latch or latch switch failure / no operating latch / latch not operating.F5 E2Door switch fault.F5 E4Latch switch fault.F5 E6Centertap voltage failure (Tulsa/Celaya).F5 E7Unlock door error / cannot unlock door.F5-E0Oven sensor opened.F5-E0 (door)Door and switches do not agree.F5-E1Oven sensor shorted.F5-E1 (latch)Door latch not operating.F5-E2BAKE/BROIL range over temperature.F5-E2 (latch)Latch error during CLEAN.F5-E3CLEAN range over temperature.F6 E4Lost communication between power board and display board.F6 E5Cancel key error.PFPower failure (not a failure mode, informational only).
Service modes (13)
- KitchenAid EZ373 & 520 Test ModeAvailable for first 60 seconds after power up. Press
- KitchenAid GOC Clock Manual DiagnosticsWithin 120 seconds of power up
- Last Fault Code RecallPress and hold CANCEL/OFF key for 5 seconds to display the last error code.
- Oxford GOC Clock Manual DiagnosticsWithin 120 seconds of power up
- Temperature Adjustment (Temperature Knob)Press and hold CLOCK pad for 5 seconds
- Temperature Adjustment (Touch Pads Only)Press and hold BAKE pad for 5 seconds
- Test mode (diagnostic)Within 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds
- Test/Diagnostic ModeWithin 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds. The…
- Whirlpool EZ175 & 176 Self-Diagnostic Test ModeAvailable for first 60 seconds after power up. 1) Simultaneously press BAKE and CLOCK. 2) Display…
- Whirlpool EZ300 Self-Diagnostic Test ModeAvailable for first 60 seconds after power up. 1) Sequentially press
- Whirlpool EZ354, 357, 358, & 410 Test ModeAvailable for first 60 seconds after power up. Press
- Whirlpool EZ625 Diagnostic Test1) Disconnect power for at least 15 seconds, then reconnect. 2) Within one minute of power up, press
- Whirlpool GOC Clock Manual DiagnosticsWithin 120 seconds of power up
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass