mypros+
Error code reference

Whirlpool Cooktop Error Code F0E2

Main relay is stuck in the closed position and cannot open.

Whirlpool codesWhirlpool cooktop codes

Main relay is stuck in the closed position and cannot open.

First step from the service manual

Unplug cooktop or disconnect power. Remove the glass to access the inside of the cooktop. Replace IPC.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F0E2.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F0E2 means on a Whirlpool cooktop

The F0E2 error code on a Whirlpool cooktop indicates that the main relay has become stuck in the closed position, meaning it cannot open when commanded to do so. A relay is an electrically operated switch that controls power flow to the heating elements. Under normal operation, the relay opens and closes rapidly to regulate heat output. When the relay welds shut or fails in a closed state, the cooktop loses the ability to cut power to the burner circuit, which creates a potentially dangerous condition where a burner may remain energized even when turned off.

The component responsible for controlling this relay is the IPC, or Induction Power Control board. This board governs the switching behavior of the relay and monitors its state. When the IPC detects that the relay is not opening as expected, it triggers the F0E2 fault to alert the user and disable safe operation. The failure can result from a relay that has physically welded its contacts together due to repeated high-current switching, or from a faulty IPC that is no longer sending the correct signals to actuate the relay.

Diagnosing this fault requires disconnecting power to the cooktop before beginning any inspection. The glass top must be removed to access the internal components. Because the relay is integrated into or directly controlled by the IPC board, the recommended repair is replacement of the IPC. Inspecting the board for visible burn marks, damaged solder joints, or a relay with fused contacts can help confirm the failure point before ordering parts.

Source: manufacturer service documentation.

Common causes of F0E2

  1. 01

    Welded relay contacts on the IPC board

    Part replacement

    High-current switching over time can cause the relay contacts to physically fuse together, preventing the relay from opening. This is the most common cause of an F0E2 fault and requires IPC board replacement.

  2. 02

    Failed IPC board not actuating the relay

    Part replacement

    The IPC board may have failed internally and is no longer sending the correct signal to open the relay, even though the relay contacts themselves are not physically welded. Board-level damage or component failure produces the same fault code.

  3. 03

    Burn damage or heat stress on the IPC board

    Part replacement

    Excessive heat buildup inside the cooktop cavity can degrade solder joints and components on the IPC board, leading to relay control failures. Visible burn marks or discoloration on the board can confirm this cause.

  4. 04

    Power surge or voltage spike

    Part replacement

    A sudden voltage surge can damage relay drive circuitry on the IPC board, causing it to lose the ability to control relay state. This type of damage is often not visually obvious and is confirmed by board replacement.

See the test procedure for each cause

Frequently asked questions about F0E2

What does F0E2 mean on a Whirlpool cooktop?
F0E2 means the main relay inside the cooktop is stuck in the closed position and cannot open. The relay is responsible for controlling power to the heating elements, and when it fails in the closed state, the cooktop cannot safely shut off the burner circuit. Whirlpool's diagnostic procedure calls for replacing the IPC, which is the Induction Power Control board that governs the relay.
Can I reset the cooktop to clear the F0E2 error?
A simple power reset is unlikely to clear the F0E2 error because it indicates a physical or electronic component failure, not a temporary software glitch. If the relay contacts are welded shut or the IPC board has failed, the fault will return immediately after power is restored. The underlying hardware issue must be repaired before the code will clear.
Is it safe to use my cooktop while the F0E2 code is active?
No, you should not use the cooktop while F0E2 is active. A relay stuck in the closed position means a burner element may remain powered even when the control is set to off, creating a serious burn and fire hazard. Disconnect power to the cooktop until the repair is completed.
How do I fix the F0E2 error on a Whirlpool cooktop?
Fixing F0E2 requires disconnecting power to the cooktop, removing the glass top to access the internal components, and replacing the IPC board. This repair involves working near high-voltage components and requires disassembling the cooktop, so it is recommended for experienced technicians or confident DIYers familiar with appliance repair safety procedures.
How much does it cost to repair an F0E2 error on a Whirlpool cooktop?
The total repair cost depends on the price of the IPC board and whether you use a professional technician or complete the repair yourself. Parts alone typically range from around $80 to $200 or more depending on the specific model. Professional labor charges can add another $100 to $200, bringing total repair costs to a range of roughly $180 to $400 in most cases.

Related Whirlpool cooktop codes

All Whirlpool cooktop codes
View all 76 Whirlpool cooktop codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass