Skip to main content
Error code reference
Whirlpool Cooktop Error Codes
79 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
Blinking HFixed coil temperature error.C-81Over temperature condition detectedC-82Over temperature condition detectedC-83Temperature sensor stuck on induction cooktop (Type 2 failure).E8Generator synchronization error.E9Temperature measurement error.EAGenerator error.ECSoftware error (Er64).EFHardware error (Er65).F-12Coil under currentF-12 E-12Coil under current on the power control board, affecting only one burner (Type 1 failure).F-21Supply power frequency errorF-21 E-00Supply power frequency error from the power control board, affecting all burners on that…F-25Stuck fan on Induction Power System (IPS), right or left side fan depending on which side…F-25 E-25Stuck fan on power control board (right or left side fan, depending on which side of the…F-36Temperature sensor is not workingF-36 E-36Temperature sensor is not working (Type 1 failure).F-37Temperature sensor is not workingF-37 E-37Temperature sensor is not working (Type 1 failure).F-40Stuck fan on Induction Power System (IPS) (Right or left side fan, depending on which…F-40 E-XXPower control board failure error where XX will describe one of 13 possible causes (Type…F-42Power supply issueF-42 E-00Power supply error from the power control board (Type 2 failure).F-43Under voltage on induction cooktop (Type 2 failure).F-43 E-00Power supply error from the power control board (Type 2 failure).F-47Power supply from power control board to User Interface is missing, or WIDE communication…F-47 E-35Power supply from power control board to User Interface is missing, or WIDE communication…F-47 E-39Power supply from power control board to User Interface is missing, or WIDE communication…F-47 E-47Power supply from power control board to User Interface is missing, or WIDE communication…F-56Power supply from Induction Power Control (IPC) to User Interface is missing or WIDE…F-56 E-00Wrong or invalid configuration, disabling the entire cooktop (Type 3 failure).F-58Wrong or invalid configurationF-58 E-58Wrong or invalid configuration on the power control board (Type 2 failure).F-60UI (User Interface) does not workF-61IPC does not workF-81 E-00Over temperature condition due to insufficient ventilation (Type 2 failure).F-82 E-00Over temperature condition due to insufficient ventilation (Type 2 failure).F0E0No error codes present in the systemF0E1Cookware is detected but it is not compatible with the requested operation or not well…F0E2Main relay is stuck in the closed position and cannot open.F0E3Coil NTC open / Coil NTC short / Coil NTC stuck.F0E4Inverter under currentF0E5The control panel switches off because of excessively high temperatures.F0E6Product supply error including possible fuse track action, mains line frequency issue…F0E7Wrong power cord connectionF0E8Wrong IPC configurationF0E9The control panel switches off because of excessively high temperatures.F0EAThe control panel switches OFF because of excessively high internal temperatures of…F0ECCoil NTC open circuit detected.F0EDCoil NTC open / Coil NTC short / Coil NTC stuck.F1-E2Lower RTD uncalibrated (internal oven control failure).F1-E5Sensor usage out of range (internal oven control failure).F1-E9WIDE Queue full.F1E0Replace UI or Model MismatchF1E1Inverter checks failureF1E3Internal CPU checksum errors.F1E7User interface board failure (check user interface).F2-E0Keypad disconnected from oven control.F2E1Stuck or shorted keypad detectedF2E2Key sensitivity problem on the touch control module.F3-E1Main oven temperature sensor open or shorted (lower oven).F3E0One or more keys permanently pressed on the touch control module.F3E2Oven temperature sensor fault (implied secondary main sensor fault).F3E6Temperature probe hardware error.F5-E0Door and door position switch(es) do not agree during Clean mode.F5-E1Door latch not operating during Clean mode.F6-E2Over temperature during clean mode (runaway temp).F6-E3Over temperature in warming drawer (runaway temp).F6E0User Interface lost communication contactF6E1Communication errorF6E4User Interface and Appliance Manager state status mismatch.F6E6Appliance Manager 1 (Copernicus) lost communication contact (WIN bus communication…F6E8Communication error.F6E9Appliance Manager 2 (Expansion Board) lost communication contact (WIN bus communication…F6EAUser Interface over temperatureF7E5Fan speed errorF7E6Fan blockedF9E0Mis-wire of the product detected; 240VAC applied across the control instead of 120VAC…U400Over voltage condition.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for unlimited access to all brands and Max AI diagnostics.
More Whirlpool error codes
Common questions
How do I find the error code on my Whirlpool Cooktop?
Most Whirlpool cooktops show the code directly on the control panel display. If your model has no display, it can be read by entering diagnostic mode with the key sequence for your model. The full procedures include model-specific instructions for reading codes.
Are these codes specific to my model?
The codes here apply broadly to Whirlpool cooktops. Meanings and diagnostic steps can vary by model and production year, so enter your model number for model-specific information and procedures.
What do I do if my code is not listed?
Some codes are model-specific or only appear in diagnostic mode. Enter your model number to get codes specific to your unit, or contact us. We update the database continuously from manufacturer service documentation.
How much does it cost to access the full diagnostic procedures?
A 3-day pass is $9.95 one-time and gives full access to all brands, codes, and procedures. Monthly access is $29/month with unlimited access to everything including Max AI diagnostics.