Skip to main content
Error code reference
Whirlpool Microwave Error Codes
153 error codes documented with diagnostic procedures.
Have your model number? Get codes specific to your unit.
-F2-Keyboard failure-F3-Thermistor failure88:88Normal display when microwave is plugged in with door open and all switches are open…888:88Displayed after power has been interrupted to indicate a power interruption has occurred.All Other CodesElectronic control malfunction.dr 0Low voltage door switch test indicates door and door switch are open.dr CSecondary interlock switch test result indicating door is closed and switch is open…dr OSecondary interlock switch test result indicating door is open and switch is closed…E1Keypad not connected.E1 E5Oven user interface failure.E2Temperature sensor opened.E3Temperature sensor shorted.E4Oven temp too high.Enter clockPower failure has occurred; display flashes 'Enter clock' until CANCEL is pressed.ERREEPROM error.ERR 0Convection temperature sensor error-sensor not connected or short-circuited.ERR 1Short circuit in the MW (microwave) relay.ERR 2Keyboard error.ERR 3Key error when one of the buttons is pressed longer than 1 minute.ERR 5Magnetron temperature sensor error.ERR 6Weight sensor calibration was not performed correctly.ERR 8Impossible to write to E2 PROM.ERR 9Options were not correctly selected.ERR ANo wheel detected on weight sensor.ERR BNo pulses from the weight sensor or frequency less than 4267 Hz.ERR CFuzzy temperature sensor error-temperature not within 19°C to 41°C range.ERR dNTC overheat protection on the magnetron is faulty (not connected or short circuit).Err4Ambient temperature sensor value is outside the allowed range (displayed during…Err7Humidity sensor PWM value out of allowed range (displayed during diagnostic test mode…ErrorGeneral error indication displayed on the control panel, accompanied by tones, indicating…F0Default F codeF0-E0Default F code-no failureF1No displayF1 E0Check oven user interfaceF1 E2Check microwave user interfaceF1 E3Check microwave appliance managerF1 E5Check microwave inverterF1:CFHardware configuration mismatch between electronic control board and display board.F1:PrSoftware type mismatch in electronic control board.F10Display error.F1E1Internal errorF1E3-0ACU Relay FailureF1E3-AMWO Cooling Fan FailureF1E4Microwave relay (Relay 4903 on PCBA) failureF1E6Microwave oven wave guide thermistor failure.F2-E0Temperature sensor opened (R=2875 ohm by spec).F2-E2Oven temp too highF2-E3Electronic control malfunction (E3, E4, & E5 variants).F2-E4Electronic control malfunction (E3, E4, & E5 variants).F2-E5Electronic control malfunction (E3, E4, & E5 variants).F2-E6CANCEL key drive line open.F2.H1Hood/light switch stuck.F2.H2Hood/light switch defective.F2.Q1User interface board (UIB) is not reading keypad inputs.F2E1Power failure indication; "Enter clock" flashes on the display after a power failure.F2KKey or foil pressed more than 1 minute.F2TTouch panel (LCD) pressed more than 1 minute.F3 E2Warming drawer sensor shorted or open (oven not equipped with this feature).F3-E0Door is open but latch is locked (door switch open indicating open door, latch switch…F3-E1Oven temp too highF3-E3Oven temp too highF3.H1Humidity sensor failure.F3.T1UIB (user interface board) thermistor failure.F3.T2FC (forced convection) thermistor failure.F3.T3Hood thermistor error.F3.T4Magnetron thermistor failure.F3CCavity temperature sensor failure.F3E3-0Meat Probe FailureF3E4Main oven powered accessory (PA) sensor open or shorted.F3E6Powered Accessory (PA) over temperature.F3E8IR sensor failureF3HHumidity sensor failureF3TTemperature sensor out of range.F4Microwave sensors failureF4-E0Meat probe shorted.F4E1Cavity NTC failureF4E1-0Cavity NTC FailureF4E1-1Cavity NTC FailureF4E2Microwave internal (ambient) temperature sensor failure (integrated on MW appliance…F4E3Hood NTC failureF4E4Humidity sensor failureF4E5Microwave weight sensor not within normal value.F4E6Microwave wave-guide heat sensor failure.F4E7Microwave probe failure.F4E8Microwave Oven Humidity Sensor Error.F4E9MW relay synchronization Error 1F4EAToast NTC failure-OpenedF4EA-0Toast NTC FailureF4EA-1Toast NTC FailureF5Microwave door switch not operating correctly (no specific E code identified for…F5-E0Door is open but latch is locked (door switch is open indicating open door, and latch…F5-E3Microwave cavity over temperature during cooking.F5-E5Self-clean temperature 288°C (550°F) not reached within 45 minutes.F5-E7Self-clean latch will not unlock.F5E1Door latch not operatingF5E2Open door failureF5E4Latch not operating (lower oven).F5E6Oven user interface lost communication.F6Return line not connectedF6 E0Oven user interface lost communication / Oven appliance manager lost communication.F6 E5No cavity size commandF6 E6Oven user interface or oven appliance manager lost communication.F6 EAOver temperature (two contextsF6:E0Communication error between display board and electronic control board.F6E1ACU/HMI communication faultF6E1-0ACU/HMI Communication FaultF6E2Excessive oven temperature in Clean mode.F6E3Mini oven/warm drawer over temperatureF6E4Lost communications with Microwave Oven Appliance Manager.F6E8Lost communications with Microwave Oven Appliance Manager (also listed as Oven appliance…F6E9Oven appliance manager-lost communication (lower oven).F7Power magnetron interruptedF7E0Insufficient water level, or excessive heating time to boil water (steam system).F7E1Boiler over temperature condition.F7E2Boiler NTC temperature sensor out of range.F7E3Improper filter resetF7E4Conductivity sensor not connected.F7E9Vent errorF8Electronic control module failure.F8-E4Oven over temperature while door close and latch unlock (E4 variant).F8E0Low fan speed underspeedF8E1Low fan speed overspeedF8E2High fan speed underspeedF8E3High fan speed overspeedF8E5Exhaust air template detector (exhaust air temperature sensor) failure.F9Relay control board communications error.F9.QTouch communication error between UIB and touch panel board.F9CE2PROM Checksum error.F9EE2PROM empty.F9E0Product not wired correctly (house wiring issue, neutral may be switched with L1 or L2).F9ME2PROM (Electrically Erasable Programmable Read-only Memory) missing.F9WE2PROM write error.FAILDuring the flex switch continuity test, one or more switches are closed when they should…FAIL 2Damper motor failureFAIL 4Convection thermistor is outside its maximum operating range (open or shorted), displayed…FBE4MWO Cooling fan error.FCE1Loss of communication between Wi-Fi module and control.FCE2Exhaust air template detector failure (HF NTC thermistor failure).FCE3Appliance failed to connect to the wireless router.FCE7Appliance failed to connect to the wireless router.FDE3Hood fan relay failureFDE4MWO Cooling fan errorFlashing colon ":"Power failure indication.Microwave Oven Inverter ErrorMicrowave oven inverter communication or operation error.MV-4903MW Relay failure (relay contact on ACU has welded closed).No DisplayThermal fuse, Copernicus Appliance Manager, or User Interface failure causing blank…noCFSoftware configuration error in display board.NTC OPENHF NTC thermistor is open (displayed as 'NTC OPEN, CALL FOR SERVICE' scrolling on…NTC OPEN, CALL FOR SERVICEHood NTC thermistor has an open circuit condition.NTC SHORTHF NTC thermistor is shorted (displayed as 'NTC SHORT, CALL FOR SERVICE' scrolling on…NTC SHORT, CALL FOR SERVICEHood NTC thermistor has a short circuit condition.PROBEMissing probe or invalid probeSABOven is in Sabbath Mode.
Get the full diagnostic procedure for any code
Step-by-step tests, expected values, wiring diagram references, and verified part numbers.
Get Started $9.95 3-day pass$29/month for all brands and Max diagnostics, with 70 Max messages a day. Plus applicable tax.