Skip to main contentGet Started
Error code reference
Whirlpool Cooktop Error Code F0EC
Coil NTC open circuit detected.
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
What the F0EC error code actually means
Your Whirlpool cooktop has detected that the temperature sensor for one of the induction coils has lost its electrical connection. The cooktop has shut down that burner zone to prevent it from overheating without any temperature monitoring. This is a safety-related error that needs to be diagnosed before the cooktop is used again.
Diagnostic procedure
The full F0EC procedure
Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.
MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Wait for the hob to cool down. Unplug cooktop, remove glass, check coil NTC connection; if disconnected reconnect, if connected but bad replace coil, if NTC and connection are OK replace IPC.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F0EC procedure $9.95
Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.
Most common causes of F0EC
Ranked by how often they cause this code
- 1Loose or disconnected NTC connector
- 2Failed coil NTC thermistor
- 3Damaged or corroded NTC wiring
- 4Faulty IPC board
Most DIYers save hundreds by diagnosing before ordering parts.
Get Started
$29/month · Cancel anytime · Or $9.95 3-day pass
Questions people ask about F0EC
What does F0EC mean on a Whirlpool cooktop?
F0EC indicates that the cooktop has detected an open circuit in the NTC thermistor associated with one of the induction coils. The NTC is a temperature sensor that the control board uses to monitor coil heat levels. When the circuit is broken or the sensor is disconnected, the board cannot safely regulate that burner zone and shuts it down. The error points to a wiring, thermistor, or control board issue that must be resolved before the cooktop is safe to operate.
Is it safe to use my Whirlpool cooktop while F0EC is displayed?
No. The F0EC error means the affected induction zone has no active temperature monitoring, so the safety system cannot prevent that coil from overheating. The cooktop disables that burner zone for this reason. Do not attempt to bypass the error or continue cooking on the affected zone until the fault has been diagnosed and corrected.
How much does it cost to repair an F0EC error on a Whirlpool cooktop?
If the fix is simply reseating a loose connector, the cost is minimal, just your time or a basic service call fee. If the coil assembly needs to be replaced, parts and labor can range from roughly $150 to $350 depending on the specific model and local labor rates. An IPC board replacement is typically in the $200 to $450 range including parts and labor. Getting a diagnostic visit from a technician first will help identify the exact component before committing to repair costs.
Can I fix the F0EC error myself?
A disconnected NTC connector is something a confident DIYer can address by unplugging the cooktop, removing the glass top, and reseating the connector. However, if the thermistor or IPC board needs to be replaced, the repair involves working with the internal electronics and wiring of the cooktop. If you are not comfortable working with appliance electronics, a qualified technician is the safer choice.
Will resetting the cooktop clear the F0EC error?
Unplugging the cooktop and restoring power may temporarily clear the error code display, but if the underlying fault (a disconnected, damaged, or failed NTC thermistor) is still present, the code will return as soon as the cooktop is used again. A reset is not a fix and should only be done as part of the diagnostic process, not as a workaround.
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass