mypros+
Model reference

Bosch SHE6AF02UC

Dishwasher

6 documents41 error codes15 service modes

Available documentation

Service Manual

  • Ascenta Dishwasher SHE6AF02UC Service Information50 pg
    Covers this model
  • Bosch Dishwasher SHE6AF02UC 06 Fault Codes and Service Program2 pg
    Covers this model

Tech Sheet

  • Bosch Dishwasher SHE6AF02UC 06 Diagnostic Sheet2 pg
    Covers this model

Wiring Diagram

  • Bosch Dishwasher SHE6AF02UC 06 Wiring Diagram1 pg
    Covers this model

Service Flash

  • Replacing stiff 645141 door seals1 pg
    Covers this model

Troubleshooting

  • Bosch Dishwasher SHE6AF02UC03 Fault Codes Troubleshooting Guide1 pg
    Covers this model
MyPros+ Max

Diagnose your Bosch SHE6AF02UC.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (41)

CodeMeaning
E:00No failures recorded.E:01Power module BLDC controller failed; functional safety error.E:02Power module working (primary) relay failed; safety (backup) relay running…E:03Working (primary) relay and safety (backup) relays both failed.E:05Impulses without activation (code not used).E:06Door latch sensor not detected; functional safety error.E:08No water detected in heat pump (no load).E:09Heating element open circuit / safety relay error; power module controlling…E:10Heater resistance too high; not enough heat generated.E:11NTC1 to NTC2 internal check failed; NTC or NTC wiring harness error; functional…E:12Heater NTC comparison check failed; NTCs have different resistances.E:13Water temperature too high; boil protect level (75°C / 167°F) exceeded…E:14Flow meter error (code not usedE:15Water in base / float switch activated and dishwasher runs continually (code…E:16Volume flow without activation (code not usedE:17Water volume too high; safety float activated.E:18Water volume too low; heat pump motor load too low.E:20Heater system check failed; functional safety error (heat pump winding…E:21Heat pump is blocked/clogged; unable to circulate and clear blockage.E:23Drain pump motor coil system check failed; functional safety error (drain pump…E:24No drain flow possible; drain pump is running but unable to remove the water…E:25Drain pump unable to rotate; blockage clearing attempts failedE:26Reference cam not detected (code not usedE:28Aqua sensor failed to calibrate properly.E:30Overvoltage detected.E:31Overloaded heat pump.E:32Overloaded drain pump.E01Pump activation / pump switching defect.E02Defective working-relay.E03Door latch defective.
View all 41 error codes
E06Not filling, drain pump active.E09Heating error / Main pump detects low water level.E11NTC error, error in wiring to NTC.E12Water temp too high (>75°C)E15Safety-switch activated, dishwasher can't be turned off.E20Winding-resistance of the main pump is wrong.E21Blocked main pump.E22Winding-resistance of the drain pump is wrong.E24Draining not possible.E25Blocked drain pump, no drain-pump-cover.E28Aqua Sensor

Service modes (15)

  • Basic settings (Extra Dry / Rinse Aid)Turn dishwasher on, press and hold '>' button, then press and hold Start button. On LED models
  • Customer Service Program1
  • Customer Service Program (S36KMK/13902/13903/13909 models)["Enter the Special Function Menu as described (LED B will be solid, LED C will flash, and 'P0'…
  • Customer Service Program (SHE/SHX/13912/13913/13919 models)["Enter the Special Function Menu as described (LED A will flash and LED B will be solid)","Press…
  • Customer service test program (P1)Enter Special programs (press and hold '>' and Delay buttons, then turn dishwasher on)
  • Error code program (P0)Enter Special programs (press and hold '>' and Delay buttons, then turn dishwasher on)
  • Failure Storage1
  • Failure Storage (S36KMK/13902/13903/13909 models)["Enter the Special Function Menu","Press the C button to access failure storage","Use the C button…
  • Failure Storage (SHE/SHX/13912/13913/13919 models)["Enter the Special Function Menu","Press the '>' button to access failure storage","Use the '>'…
  • Reset (Cancel - drain)Press and hold Start button until Active light goes out or when display shows '0.01'.
  • Sales demo (showroom) program (P7)Enter Special programs (press and hold '>' and Delay buttons, then turn dishwasher on)
  • Special Function Menu["Ensure unit is powered off","Press and hold any two buttons","While holding buttons, turn the…
  • Special Function Menu (SHE models)While pressing the ">" button and the "delay" button, turn the dishwasher on with the main switch
  • Special Function Menu (SHX models)While pressing the ">" button and the "<" button, turn the dishwasher on with the main switch
  • Special programs (service menu)Press and hold '>' and Delay buttons, then turn dishwasher on

Full entry steps, exit procedures, and test sequences are available in Max.

Related Bosch dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass