Model reference

Frigidaire LTF7000ES0

Washer

3 documents48 error codes5 service modes

Available documentation

Service Manual

Technical Service Manual 2009 3 5 Cu Ft Affinity Front Load 6000 and 7000 Series74 pg
Covers this model

Service Flash

Service Flash LN063 Affinity Washers Enter Continuous Cycle Loop, Error Message Displayed1 pg
Covers this model

Training

Technical Service Manual 2006 Technical Training Manual139 pg
Covers this model

MyPros+ Max

Diagnose your Frigidaire LTF7000ES0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Frigidaire Washer

E11 on my Frigidaire LTF7000ES0

M+

Fill time too long — water is not

From Service Manual 995903, p.35:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part 5304504863

Electronic control board

Error codes (48)

CodeMeaning

E11Fill time too long E13Water leak in tub or air leak in the air bell system.E21Water not pumping out fast enough.E23Drain pump relay on control board failed.E24Drain pump relay on control board failed.E31Pressure sensor not communicating with control board.E35Pressure sensor indicates water overfill.E36Control board problem.E41Control board thinks the door switch is open.E43Board communications problem.E44Board communications problem.E45Board communications problem.E46Board communications problem.E47Board thinks the door PTC circuit is open in spin.E48Board thinks the door PTC circuit is closed.E52Bad signal from tachogenerator.E56High motor current.E57High current on inverter.E58High current on motor phase.E59No tacho signal for 3 seconds.E5AHigh temperature on heat sink.E5BHigh temperature on heat sink.E5CHigh temperature on heat sink.E5DCommunication problem between control board and speed control board.E5ECommunication problem between control board and speed control board.E5FCommunication problem between control board and speed control board.E66Heating element relay failure.E67Input voltage on microprocessor incorrect.E68Current leakage to ground on heater or fuse opened.E74Wash temperature does not increase.

View all 48 error codes

E75Water temperature sensor circuit problem.E76NTC temperature for the cold water valve over the limits.E82Console control problem.E83Console control problem.E91Selector LEDs do not light up.E93Console control problem.E94Console control problem.E95Communication error.E97Console control problem.E98Console control problem.EB1Incoming power frequency out of limits.EB2Incoming line voltage above 130 VAC.EB3Incoming line voltage below 90 VAC.EBEConsole control problem.EBFConsole control problem.EF1Clogged drain pump.EF2Too much soap (oversudsing).EF5NTC temperature for hot water valve over the limits.

Service modes (5)

clear_error_code["Turn the Program Knob to start position (Spin Only).","Press START/PAUSE to start the cycle and…
control_lock["Press Options and Select at the same time and hold for 10 seconds until 'LOC' is displayed…
diagnostic["Turn Program Knob to the start position (Spin Only).","Press START/PAUSE to start the cycle and…
read_error_codes["Wake the washer by pressing any button.","Wait 5 seconds.","Press and hold the START/PAUSE and…
reset_factory_settings["Press Start/Pause and Select at the same time and hold until a signal sounds."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Frigidaire washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass