mypros+
Model reference

Maytag MAH2400A

Washer

5 documents22 error codes22 service modes

Available documentation

Tech Sheet

  • Laveuse à chargement frontal de 61 cm – Informations techniques14 pg
    Covers this model
  • 24" Front Load Washer⎯Technical Information12 pg
    Covers this model
  • techsheet 16027174f fr14 pg
    Covers this model

Service Manual

  • Neptune Commercial High Efficiency Washer Service Manual124 pg
    Covers this model

Other

  • MAH2400A Samsung Technical12 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MAH2400A.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (22)

CodeMeaning
3EDrive system is not working correctly; motor speed indicator error and motor…bEMotor tach signal exists without motor running; tach signal exists without…d10Door lock sense error or due to power line interference; spins inhibited until…d11Motor speed error detected; cycle paused but can be restarted.d13Blocked coin 2 or coin drop control circuit failure; coin recognition and price…d16Not receiving communications from installed debit card reader in Generation 2…d17Door was not locked at the beginning of final spin (MAH21 models).d4Washer door sense error on control board or due to power line interference…d5Blocked coin 1 or coin drop control circuit failure; coin recognition and price…d7Slow fill detected during previous cycle; maximum fill time or max continuous…d8Last drain was slow (drain time greater than 2 minutes).d9Low voltage detected; less than 90 volts AC for 8 seconds.dcDistribute ClothesdLLatch UnlockedFLThe washer failed to lock the door after 3 attempts.LEWater fill error; input signal from water level sensor is out of range, washer…LOThe door will not unlock after 3 attempts.ndNo DrainnFNo FillodOpen the DoorOEA fault is detected in the water level sensor; data (frequency) shows the water…tESump thermistor failure due to abnormal high/low temperature or ohm resistance…

Service modes (22)

  • Board Input TestWhile in Service Mode, press the Temperature key.
  • Board Output / System Test["Enter Service Mode.","Press Temperature and Extra Rinse simultaneously to start the Board Output…
  • Board Output TestWhile in Service Mode, press Temperature and Extra Rinse keys.
  • Board Output/System TestIn Service Mode, press Temperature and Extra Rinse simultaneously.
  • Cycle Count DisplayWhile in Service Mode, press Extra Rinse.
  • Cycle Credit["Enter Diagnostic Mode (entire display flashing).","Press the slow key (CC will display)."]
  • Diagnostic Code DisplayWhile in Service Mode, press the Chime key
  • Diagnostic Mode["Enter the Setup mode (open service door or turn service key).","Press and hold the Delicates &…
  • Display Software VersionWhile in Service Mode viewing diagnostic codes, press Soil Level
  • Fast Time Down TestWhile any test or cycle is running in Service Mode, press the Spin key to start
  • Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the Woolens keypad to start the field…
  • Help Mode["Enter Setup mode.","Navigate to Special Pricing Option mode 2.XX.","Press the Permanent Press…
  • LED/Switch TestWhile in Service Mode, press and hold the Delay Start key.
  • Operational Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the WHITES keypad to start the…
  • Quick Service CycleWhile in Service Mode, press Temperature and Soil Level keys for 3 seconds.
  • Quick Spin Cycle (MAH20 Models)["Enter Diagnostic Mode (entire display flashing).","Press the COLORS keypad to start the quick…
  • Quick Spin TestWhile in Service Mode, press Delay Start and Temperature keys.
  • Quick Stop / Advance Step["While in any Service Mode test or cycle, press Spin to initiate Quick Stop."]
  • Relay Test Mode (MAH20PN)["Enter Diagnostic Mode (entire display flashing).","Press the Permanent Press (lower left) keypad…
  • Service Mode1
  • Setup / Programming Mode["Insert access door key, turn and lift to remove the access door (PD/PS models).","For PN models
  • Software Version DisplayIn Service Mode, press Soil Level button

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass