mypros+
Model reference

Maytag MAH6500AWQ

Washer

37 documents32 error codes17 service modes

Available documentation

Tech Sheet

  • Technical Information Neptune Front Load Washer14 pg
    Covers this model
  • tech sheet 16025862F fr14 pg
    Covers this model

Service Manual

  • Instruction Sheet8 pg
    Covers this model
  • Technical Information Neptune Front Load Washer15 pg
    Covers this model
  • Instruction Sheet8 pg
    Covers this model

Bulletin

  • Technical Bulletin - TDL-0025-B New software changes operation of Spin Cycle2 pg
    Covers this model
  • Technical Bulletin - ITDL-0030-B New Spinner and Baffle design1 pg
    Covers this model
  • Technical Bulletin - TDL-0056-B Washer will stop mid-cycle1 pg
    Covers this model
  • Technical Bulletin1 pg
    Covers this model
  • TechnicalBulletin-PDL-0001-B1 pg
    Covers this model
  • Technical Bulletin - TDL-0045A-B Washer vibrates and walks during the spin cycle1 pg
    Covers this model
  • Technical Bulletin TDL-0045A-B1 pg
    Covers this model
  • Technical Bulletin - Washer vibrates and walks during the spin cycle1 pg
    Covers this model
  • Technical Bulletin - TDL-0046A-B Rubber cuff removed on drain hose1 pg
    Covers this model
  • Technical Bulletin - TDL-0025-B New software changes operation of Spin Cycle2 pg
    Covers this model
  • Technical Bulletin - TDL-0046A-B Rubber cuff removed on drain hose1 pg
    Covers this model
  • Technical Bulletin - Rubber cuff removed from drain hose1 pg
    Covers this model
  • Technical Bulletin - TDL-0051A-B Door boot wrinkles2 pg
    Covers this model
  • Technical Bulletin - Door boot wrinkles2 pg
    Covers this model
  • Technical Bulletin - TDL-0066-B-French Front Load Light Removal1 pg
    Covers this model
  • Technical Bulletin - TDL-0066-B Front Load Light Removal1 pg
    Covers this model
  • Technical Bulletin TDL-0066-B1 pg
    Covers this model
  • Technical Bulletin - TDL-0066-B-French Front Load Light Removal1 pg
    Covers this model
  • Technical Bulletin - TDL-0066-B Front Load Light Removal1 pg
    Covers this model
  • Technical Bulletin - Neptune Door adjustment2 pg
    Covers this model
  • Technical Bulletin - Inertial Unbalance Switch Relocation1 pg
    Covers this model
  • Technical Bulletin - Improved Lip Seal2 pg
    Covers this model
  • Technical Bulletin - Serial tag missing model and serial numbers1 pg
    Covers this model
  • Technical Bulletin - New universal motor/motor control conversion kit1 pg
    Covers this model
  • Technical Bulletin1 pg
    Covers this model
  • TechnicalBulletin-TDL-0044B-B1 pg
    Covers this model
  • Technical Bulletin - Motor Drive System Neutral Feed Issue1 pg
    Covers this model

Service Flash

  • STOP – Before Proceeding With Repair (Read This Warning)2 pg
    Covers this model

Tech Tip

  • Instruction Sheet13 pg
    Covers this model
  • Instruction Sheet4 pg
    Covers this model

Other

  • TDL 0041 S1 pg
    Covers this model
  • TCL 0015B B1 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MAH6500AWQ.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (32)

CodeMeaning
01No drain02Door will not unlock after 11 attempts.03No fill04Door will not lock after 11 attempts.05Continuous unbalance circuit during spin only.06Locked rotor07Heater not heating08Water level sensor failure10Unbalanced load at low speed11Non-volatile memory error15Stuck key16High speed not reached due to high motor torque17Door actuator switch not detected as open since final spin18Door switch detected open during cycle19Door lock sensor or motor control relay failure20Door switch input detected open during cycle.21Sensor switch failure on machine control board22Door switch detected open during cycle23Door will not unlock24Motor overspeed25Motor tachometer signal present although the motor is not running28Valve thermistor failure29Tub collector thermistor failuredoThe door of the machine is open.FLThe machine has repeatedly tried to lock the door but cannot.LODoor is locked (failed to unlock)LrLocked rotorndNo drainnFThe machine has tried to fill but cannot.odThe door has not been opened since the end of the last cycle; as a safety check…
View all 32 error codes
PFPower to the machine has been lost during the last cycle; may occur on start up…SdMachine has detected a high level of suds and will alter its cycle for this…

Service modes (17)

  • Board Input TestWhile in Service Mode, press the Hand Wash key.
  • Board Output TestWhile in Service Mode, press the Rinse key.
  • Diagnostic Codes AccessIn service mode, press the 'presoak' button
  • Diagnostic Codes ViewWhile in Service Mode, press the Presoak key
  • Diagnostic Codes ViewingWhile in Service Mode, press the Presoak key
  • Fast Time Down TestWhile in Service Mode, press the Quick key.
  • Membrane Keypad TestIn service mode, press the 'wrinkle free' button.
  • Membrane Pad CheckWhile in Service Mode, press the Wrinkle Free key.
  • Membrane Pad Check TestWhile in Service Mode, press the Wrinkle Free key.
  • Motor Control Board Output Test1) Disconnect power. 2) Remove front panel and pull JP4 connector from motor control board. 3)…
  • Motor Torque DisplayWhile in Service Mode, press the Normal key.
  • Quick Service CycleWhile in Service Mode, press the Delicates key.
  • Quick Spin TestWhile in Service Mode, press the Spin key.
  • Quick Stop Time TestIn service mode, press the 'quick' button.
  • Service ModePress and hold the Delicates and Heavy Soil keys simultaneously for 3 seconds
  • Software Revision DisplayIn service mode, press the 'light soil' button.
  • Software Revision Number DisplayWhile in Service Mode, press the Light Soil key.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass