Model reference

Samsung WF45T6000AW/A5-00

Name: Samsung WF45T6000AW/A5-00
Brand: Samsung

Washer

1 document28 error codes6 service modes

Available documentation

Service Manual

WASHING MACHINE DRUM TYPE Service Manual38 pg
Covers this model

MyPros+ Max

Diagnose your Samsung WF45T6000AW/A5-00.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Samsung Washer

1C on my Samsung WF45T6000AW/A5-00

M+

Water level sensor error caused by

From Service Manual 855856, p.28:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part DA92-00384N

Main PCB assembly

Error codes (28)

CodeMeaning

1CWater level sensor error caused by damaged/clogged/folded hose, hose engagement…3CMotor driving error and hall sensor error caused by disconnected motor/hall…4CWater supply error caused by foreign material in water supply valve…4C2Water supply error where water temperature is sensed as higher than 50°C in…5CDrain error caused by damaged pump motor impeller, wrong voltage, freezing…8CVibration noise during SPIN cycle with small amount of clothes (e.g., 1 bath…8C1Error detected in the Mems PBA or data error detected.8C2Error detected in the Mems PBA or data error detected.9C1Power error caused by under or over voltage supply, use of plug receptacle…9C2Power error caused by under or over voltage supply, use of plug receptacle…ACCommunication error between the sub PBA and main PBA; signals not sensed due to…AC3Communication error between the DR Module and main PBA; signals not sensed due…AC4Communication error between the WIFI Module and main PBA; signals not sensed…AC5Communication error between the LCD Module and main PBA; signals not sensed due…AC6Communication error between the Inverter PBA and main PBA; signals not sensed…BC2Switch error where a button other than Power is continually pressed for more…DCDoor error caused by switch contact error from deformation of door hook, door…DC1Door lock error where door is not locked after door close operation, caused by…DC3Add door error related to main PCB fault or bending connector.DDCAdd door is opened; check add door switch, barrier, and lock module movement.HCHeater error caused by short-circuited or disconnected washing heater wire…HC1Heater error caused by short-circuited or disconnected washing heater wire…LCWater leakage error caused by heater engagement fault, displaced air hose…OCOverflow error caused by water level sensor fault, continuous water supply due…SFSystem error caused by micro controller operation failure.SUDToo much foaming detected; displayed while foaming is being removed, after…TC1Temperature sensor error caused by faulty washing or dry temperature sensor…UBUnbalance error caused by laundry contents creating an unbalanced load in the…

Service modes (6)

Automatic check modeEnter Smart Install mode, then press Start/Pause while displaying 'AS'
Automatic Mode Result EnquiryWhile 'AS' is displayed, press 'Delay End + Start/Pause' button simultaneously.
Diagnostic Code CheckEnter Smart Install mode, then press the first button on the right at the bottom while displaying…
Manual check modeEnter Smart Install mode, then press Delay End while displaying 'AS'
S/W version checkEnter Smart Install mode, then press the first button on the left at the bottom while displaying…
Smart InstallSet the scheduled time to 17:00, then press Start/Pause for 7 seconds

Full entry steps, exit procedures, and test sequences are available in Max.

Related Samsung washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass