mypros+
Model reference

Whirlpool RF368LXPQ0

Range

3 documents36 error codes25 service modes

Available documentation

Tech Sheet

  • Whirlpool Range RF368LXPS0 Tech Sheet 97562074 pg
    Covers this model

Service Manual

  • ELECTRIC RANGE Use & Care Guide28 pg
    Covers this model
  • TECHNICAL EDUCATION JOB AID 4317368 KAC-40 FAILURE CODES AND WIRING DIAGRAMS for WHIRLPOOL AND KITCHENAID SLIDE-IN & FREESTANDING GAS & ELECTRIC RANGES80 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool RF368LXPQ0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (36)

CodeMeaning
EndEnd of a timed cooking or self-cleaning cycle; the oven has shut off…F0 E0No error(s) found (Good)F1 E0EEPROM communications error.F1 E1EEPROM checksum failure.F1 E2UL A/D error(s).F1 E3Internal error (Oxford).F1 E4Model ID error (Tulsa/Celaya); Internal error (Oxford).F1 E5Internal error (Oxford)F1 E6Latch signal mismatch error (Tulsa/Celaya); Internal error (Oxford)F1 E7Internal error (Oxford)F1 E8Internal error (Oxford)F1 E9Internal error (Oxford)F2 E0Shorted key / Stuck key.F2 E1Keytail unplugged.F3 E0Oven sensor opened.F3 E1Oven sensor shorted.F3 E2BAKE/BROIL range over temperature.F3 E3CLEAN range over temperature.F3 E4Bottom oven sensor open (Oxford); CLEAN range over temperature (Tulsa/Celaya).F3 E5Lower oven sensor shorted (bottom sensor short).F3 E6Warming drawer sensor open (WD sensor open).F3 E7Warming drawer sensor shorted (WD sensor shorted).F4 E2Over temperature during cook cycle (temperature runaway error).F4 E3Over temperature during clean cycle (temperature runaway error).F4 E7Over temperature cavity 2 (temperature runaway error in second cavity).F5Door lock error during Clean (3-digit display / knob control).F5 E0Door and switches do not agree.F5 E1Door latch not operating.F5 E2Latch error during CLEAN.F5 E4Latch switch fault.
View all 36 error codes
F5 E6Centertap voltage failure (Tulsa/Celaya).F5 E7Unlock door error / cannot unlock door.F6 E4Lost communication between power board and display board.F6 E5Cancel key error.LocControl Lock is engaged; control panel pads are disabled to prevent unintended…PFPower failure has occurred; display shows 'PF' or a flashing time when power is…

Service modes (25)

  • 12-Hour Shut-Off Toggle (Style 1)["Press and hold DELAY for 5 seconds.","'12 HR SHUT-OFF ON' will appear on the display.","Press and…
  • All Tones Toggle (Style 1)["Press and hold CLOCK for 5 seconds.","'ALL SOUNDS OFF' will appear on the display.","Repeat to…
  • All Tones Toggle (Style 2)["Press and hold STOP TIME for 5 seconds.","'Snd OFF' will appear on the display.","Press and hold…
  • Control Lock["Make sure the oven and Timer are off.","Press and hold the 'Lock' key for 5 seconds.","A single…
  • diagnostic test modeWithin 60 seconds of power up, simultaneously hold down the BAKE and CLOCK keys for 5 seconds
  • End of Cycle Tones Toggle (Style 1)["Press and hold CONVECT for 5 seconds to turn END OF CYCLE TONES off.","Press and hold CONVECT for…
  • Fahrenheit/Celsius Toggle (Style 1)["Press and hold AUTO CLEAN for 5 seconds.","'TEMPERATURE UNIT CELSIUS' will appear in the…
  • Fahrenheit/Celsius Toggle (Styles 2 & 3)["Press and hold BROIL for 5 seconds.","Repeat to change back to Fahrenheit."]
  • Key Press Tones Toggle (Style 1)["Press and hold WARM (Cooking Options) for 5 seconds.","'KEY PRESS TONES OFF' will appear on the…
  • KitchenAid EZ373 & 520 Test ModeAvailable for first 60 seconds after power up. Press
  • KitchenAid GOC Clock Manual DiagnosticsWithin 120 seconds of power up
  • last fault code displayPress and hold CANCEL/OFF key for 5 seconds until last error code is displayed.
  • Oven Temperature Calibration Adjustment (Style 1)["Press and hold OVEN LIGHT for 5 seconds until the oven display shows the current calibration…
  • Oven Temperature Calibration Adjustment (Styles 2 & 3)["Press and hold BAKE for 5 seconds until the oven display shows the current calibration (e.g…
  • Oxford GOC Clock Manual DiagnosticsWithin 120 seconds of power up
  • Reminder Tones Toggle (Style 1)["Press and hold BAKE for 5 seconds.","'REMINDER TONES OFF' will appear on the display.","Repeat to…
  • Reminder Tones Toggle (Style 2)["Press and hold TIMER SET for 5 seconds.","'rEP OFF' or 'OFF' will appear in the display.","Repeat…
  • temperature adjustmentPress and hold BAKE pad for 5 seconds. Current offset is shown in 3-digit display. CAL is shown in…
  • Tone Pitch Toggle (Style 1)["Press and hold BROIL for 5 seconds.","'TONE PITCH LOW' will appear on the display.","Repeat to…
  • Tone Pitch Toggle (Style 2)["Press and hold DELAY START for 5 seconds.","'Snd LO' will appear on the display.","Repeat to…
  • Whirlpool EZ175 & 176 Self-Diagnostic Test ModeAvailable for first 60 seconds after power up. 1) Simultaneously press BAKE and CLOCK. 2) Display…
  • Whirlpool EZ300 Self-Diagnostic Test ModeAvailable for first 60 seconds after power up. 1) Sequentially press
  • Whirlpool EZ354, 357, 358, & 410 Test ModeAvailable for first 60 seconds after power up. Press
  • Whirlpool EZ625 Diagnostic Test1) Disconnect power for at least 15 seconds, then reconnect. 2) Within one minute of power up, press
  • Whirlpool GOC Clock Manual DiagnosticsWithin 120 seconds of power up

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass