Model reference

Whirlpool WFG374LVB2

Range

7 documents36 error codes4 service modes

Available documentation

Tech Sheet

Tech Sheet - W10198618 - Rev B8 pg
Covers this model

Service Manual

Whirlpool Gas Range Direct Spark Ignition System29 pg
Covers this model
Job Aid - 30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
Whirlpool Gas Range Direct Spark Ignition System KR-2829 pg
Covers this model

Installation Guide

Installation Instructions20 pg
Covers this model
Instruction Sheet2 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WFG374LVB2.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

F0 E0 on my Whirlpool WFG374LVB2

M+

Factory default - not an error.

From Tech Sheet W11950945, p.37:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (36)

CodeMeaning

F0 E0Factory default F1Internal board failure (A/D errors)F1 E0EEPROM communications error.F1 E1EEPROM checksum error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.F1-E0Internal board failure.F1-E1Internal board failure.F2Shorted key F2 E0Shorted key.F2 E1Key tail unplugged.F2-E0Shorted key.F2-E1A/D Error(s).F2-E2A/D Error(s).F3Oven sensor opened, oven sensor shorted, BAKE/BROIL range over temperature, or…F3 E0Oven sensor opened F3 E1Oven sensor shorted F3 E2Bake range over temperature.F3 E3Clean range over temperature.F3 E4Oven sensor opened F3 E5Oven sensor shorted F3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Oven sensor opened.F3-E1Oven sensor shorted.F3-E2BAKE/BROIL range over temperature.F3-E3CLEAN range over temperature.F5Door latch not operating during Clean mode F5 E0Door switches do not agree.

View all 36 error codes

F5 E1Door latch not operating.F5-E0Door and switches do not agree (Clean mode).F5-E1Door latch not operating (Clean mode).F5-E2Door and switches do not agree (Clean mode).F8 E0N/A (no likely failure condition described).PFA reset has occurred in the Electronic Range Control (ERC), typically caused by…

Service modes (4)

Diagnostics ModePress CANCEL > CANCEL > START within a 5-second period.
Diagnostics Test Mode (Relay Checks)After entering Diagnostics Mode (CANCEL>CANCEL>START), press individual keys to test relays
Last Error Code RecallPress and hold the CANCEL/OFF key for 5 seconds until the last error code is displayed.
Temperature AdjustmentStep 1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass