Model reference
Whirlpool WFG374LVQ1
Range
9 documents40 error codes10 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10198618 - Rev B8 pg
Service Manual
- Whirlpool Gas Range Direct Spark Ignition System29 pg
- Job Aid - 30″ Freestanding Self-Cleaning Gas Range68 pg
- 30″ Freestanding Self-Cleaning Gas Range68 pg
- Whirlpool Gas Range Direct Spark Ignition System KR-2829 pg
- Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
Tech Tip
- Instruction Sheet2 pg
Installation Guide
- Installation Instructions20 pg
- Instruction Sheet2 pg
MyPros+ Max
Diagnose your Whirlpool WFG374LVQ1.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (40)
CodeMeaning
F0 E0Factory defaultF1Internal board failure (A/D errors)F1 E*Control board failure (all F1 sub-codes indicate control fault).F1 E0EEPROM communications error.F1 E1EEPROM checksum error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.F1-E0Internal board failure.F1-E1Internal board failure.F2Shorted keyF2 E0Shorted key.F2 E1Key tail unplugged.F2-E0Shorted key.F2-E1A/D Error(s).F2-E2A/D Error(s).F3Oven sensor opened, oven sensor shorted, BAKE/BROIL range over temperature, or…F3 E0Oven sensor openedF3 E1Oven sensor shortedF3 E2Bake range over temperature.F3 E3Clean range over temperature.F3 E4Oven sensor openedF3 E5Oven sensor shortedF3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Oven sensor opened.F3-E1Oven sensor shorted.F3-E2BAKE/BROIL range over temperature.F3-E3CLEAN range over temperature.F5Door latch not operating during Clean modeView all 40 error codes
F5 E0Door switches do not agree.F5 E1Door latch not operating.F5 E2Door switch fault.F5-E0Door and switches do not agree (Clean mode).F5-E1Door latch not operating (Clean mode).F5-E2Door and switches do not agree (Clean mode).F6 E*Control communication failure.F8 E0N/A (no likely failure condition described).F9House miswiredPFA reset has occurred in the Electronic Range Control (ERC), typically caused by…
Service modes (10)
- Diagnostics ModePress CANCEL > CANCEL > START within a 5-second period.
- Diagnostics Test Mode (Relay Checks)After entering Diagnostics Mode (CANCEL>CANCEL>START), press individual keys to test relays
- Last Error Code RecallPress and hold the CANCEL/OFF key for 5 seconds until the last error code is displayed.
- LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
- LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
- MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
- MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
- MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
- MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
- Temperature AdjustmentStep 1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Whirlpool range models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass