mypros+
Model reference

Whirlpool WFG381LVB1

Range

11 documents51 error codes12 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10198649 - Rev C (FR)8 pg
    Covers this model
  • Tech Sheet - W10198618 - Rev B8 pg
    Covers this model
  • Fiche technique - Tech Sheet W103575188 pg
    Covers this model

Service Manual

  • Whirlpool Gas Range Direct Spark Ignition System29 pg
    Covers this model
  • Job Aid - 30″ Freestanding Self-Cleaning Gas Range68 pg
    Covers this model
  • 30″ Freestanding Self-Cleaning Gas Range68 pg
    Covers this model
  • Whirlpool Gas Range Direct Spark Ignition System KR-2829 pg
    Covers this model
  • Troubleshooting Gas and Electric Freestanding Range Electronic Controls70 pg
    Covers this model

Installation Guide

  • Installation Instructions36 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool WFG381LVB1.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (51)

CodeMeaning
F0 E0Factory defaultF1Internal circuit board failure or A/D error(s).F1 E*Control board failure (all F1 sub-codes indicate control fault).F1 E0EEPROM communications error.F1 E1EEPROM checksum error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.F1-E0Internal board failure.F1-E1Internal board failure.F1E0Internal circuit board failure (LCC 180/190 display).F1E1A/D error (LCC 180/190 display).F1E2A/D error (LCC 180/190 display).F2Shorted key (keypad short circuit).F2 E0Shorted key.F2 E1Key tail unplugged.F2-E0Shorted key.F2-E1A/D Error(s).F2-E2A/D Error(s).F2E0Shorted key (LCC 180/190 display).F3Oven sensor—open circuit.F3 E0Oven sensor openedF3 E1Oven sensor shortedF3 E2Bake range over temperature.F3 E3Clean range over temperature.F3 E4Oven sensor openedF3 E5Oven sensor shortedF3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Oven sensor opened.
View all 51 error codes
F3-E1Oven sensor shorted.F3-E2BAKE/BROIL range over temperature.F3-E3CLEAN range over temperature.F3E0Oven sensor—open circuit (LCC 180/190 display).F3E1Oven sensor—short circuit (LCC 180/190 display).F3E2BAKE/BROIL—excessive temperature.F3E3CLEAN—excessive temperature.F5Door and latch switch mismatch (clean mode).F5 E0Door switches do not agree.F5 E1Door latch not operating.F5 E2Door switch fault.F5-E0Door and switches do not agree (Clean mode).F5-E1Door latch not operating (Clean mode).F5-E2Door and switches do not agree (Clean mode).F5E0Door and latch switch mismatch during clean mode (LCC 180/190 display).F5E1Door latch not functioning during clean mode.F5E2Door and latch switch mismatch during clean mode (LCC 180/190 display).F6 E*Control communication failure.F8 E0N/A (no likely failure condition described).F9House miswiredPFA reset has occurred in the Electronic Range Control (ERC), typically caused by…

Service modes (12)

  • diagnosticPress CANCEL > CANCEL > START within 5 seconds.
  • diagnostic_test_modeAfter entering diagnostic mode (CANCEL>CANCEL>START), the initial display shows 'tSt' (LCC 90/95)…
  • Diagnostics ModePress CANCEL > CANCEL > START within a 5-second period.
  • Diagnostics Test Mode (Relay Checks)While in Diagnostics Mode, press individual keypads
  • Last Error Code RecallPress and hold the CANCEL/OFF key for 5 seconds until the last error code is displayed.
  • LCC Diagnostic Mode (LCC90/LCC95/LCC180)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • LCC190 Diagnostic Mode (Self Clean, Convection models)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME or TEMP/HOUR '+' key to cycle through…
  • MRC Diagnostic Mode["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC Diagnostic Mode (Fan/True Convection Electric - Oven Light entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' key to cycle through diagnostic…
  • MRC II Diagnostic Mode (Number 3 key entry - KitchenAid models)["Press OFF/OFF/START or CANCEL/CANCEL/START in sequence.","Press the number '3' key to cycle…
  • MRC II Diagnostic Mode (TEMP/TIME entry)["Press CANCEL, CANCEL, START in sequence.","Press TEMP/TIME '+' keypad to cycle through diagnostic…
  • Temperature AdjustmentStep 1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass