Model reference

Whirlpool WFG381LVS2

Range

10 documents47 error codes6 service modes

Available documentation

Tech Sheet

Tech Sheet - W10198649 - Rev C (FR)8 pg
Covers this model
Tech Sheet - W10198618 - Rev B8 pg
Covers this model
Fiche technique - Tech Sheet W103575188 pg
Covers this model

Service Manual

Whirlpool Gas Range Direct Spark Ignition System29 pg
Covers this model
Job Aid - 30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
30″ Freestanding Self-Cleaning Gas Range68 pg
Covers this model
Whirlpool Gas Range Direct Spark Ignition System KR-2829 pg
Covers this model

Installation Guide

Installation Instructions36 pg
Covers this model
Instruction Sheet2 pg
Covers this model
Instruction Sheet2 pg
Covers this model

MyPros+ Max

Diagnose your Whirlpool WFG381LVS2.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Whirlpool Range

F0 E0 on my Whirlpool WFG381LVS2

M+

Factory default - not an error.

From Tech Sheet W13091830, p.42:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (47)

CodeMeaning

F0 E0Factory default F1Internal circuit board failure or A/D error(s).F1 E0EEPROM communications error.F1 E1EEPROM checksum error.F1 E2UL A/D error(s).F1 E4Model ID error.F1 E6Latch signal mismatch error.F1-E0Internal board failure.F1-E1Internal board failure.F1E0Internal circuit board failure (LCC 180/190 display).F1E1A/D error (LCC 180/190 display).F1E2A/D error (LCC 180/190 display).F2Shorted key (keypad short circuit).F2 E0Shorted key.F2 E1Key tail unplugged.F2-E0Shorted key.F2-E1A/D Error(s).F2-E2A/D Error(s).F2E0Shorted key (LCC 180/190 display).F3Oven sensor—open circuit.F3 E0Oven sensor opened F3 E1Oven sensor shorted F3 E2Bake range over temperature.F3 E3Clean range over temperature.F3 E4Oven sensor opened F3 E5Oven sensor shorted F3 E6Warming drawer sensor open.F3 E7Warming drawer sensor shorted.F3-E0Oven sensor opened.F3-E1Oven sensor shorted.

View all 47 error codes

F3-E2BAKE/BROIL range over temperature.F3-E3CLEAN range over temperature.F3E0Oven sensor—open circuit (LCC 180/190 display).F3E1Oven sensor—short circuit (LCC 180/190 display).F3E2BAKE/BROIL—excessive temperature.F3E3CLEAN—excessive temperature.F5Door and latch switch mismatch (clean mode).F5 E0Door switches do not agree.F5 E1Door latch not operating.F5-E0Door and switches do not agree (Clean mode).F5-E1Door latch not operating (Clean mode).F5-E2Door and switches do not agree (Clean mode).F5E0Door and latch switch mismatch during clean mode (LCC 180/190 display).F5E1Door latch not functioning during clean mode.F5E2Door and latch switch mismatch during clean mode (LCC 180/190 display).F8 E0N/A (no likely failure condition described).PFA reset has occurred in the Electronic Range Control (ERC), typically caused by…

Service modes (6)

diagnosticPress CANCEL > CANCEL > START within 5 seconds.
diagnostic_test_modeAfter entering diagnostic mode (CANCEL>CANCEL>START), the initial display shows 'tSt' (LCC 90/95)…
Diagnostics ModePress CANCEL > CANCEL > START within a 5-second period.
Diagnostics Test Mode (Relay Checks)While in Diagnostics Mode, press individual keypads
Last Error Code RecallPress and hold the CANCEL/OFF key for 5 seconds until the last error code is displayed.
Temperature AdjustmentStep 1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass