Model reference
Bosch SHE4AP05UC/03
Dishwasher
10 documents31 error codes31 service modes
Available documentation
Service Manual
- Bosch Ascenta Dishwasher Repair Instruction Manual49 pg
- Assccentad Dw Repair Instruction49 pg
- Repair Instructions – Dishwashers115 pg
- Ascenta Dishwasher Repair Instruction50 pg
- Ascenta Dishwasher SHE6AF02UC Service Information50 pg
- Ascent Dwrap Repair Instruction50 pg
- Ascenta Dishwasher Repair Instruction49 pg
- Ascenta Dw Repair Instruction49 pg
- Repair Instructions – Dishwashers115 pg
- SHX4AT55UC 14 Bosch Dishwasher Service Manual50 pg
MyPros+ Max
Diagnose your Bosch SHE4AP05UC/03.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (31)
CodeMeaning
E:00No failures recorded.E:01Power module BLDC controller failed; functional safety error.E:02Power module working (primary) relay failed; safety (backup) relay running…E:03Working (primary) relay and safety (backup) relays both failed.E:04Faulty safety heater relay or faulty heater.E:05Impulses without activation (code not used).E:06Door latch sensor not detected; functional safety error.E:08No water detected in heat pump.E:09Heating element burn through / safety relay error; power module controlling…E:10Heater resistance too high.E:11NTC1 to NTC2 internal check failed; functional safety error (NTC or NTC wiring…E:12Heater NTC resistances not balanced; heater NTCs have different resistances.E:13Water temperature too high; boil protect level (75°C / 167°F) exceeded…E:14Flow meter error (code not used; no flow meter).E:15Water in base (code not used for bases are open); float switch activated and…E:16Volume flow without activation (code not used; no flow meter).E:17Water volume too high; safety float activated.E:18Water volume too low; heat pump motor load too low.E:20Heater system check failed; functional safety error (heat pump winding…E:21Heat pump unable to circulate and clear blockage.E:22Water in sump (drainage/filter issue).E:23Drain pump motor coil system check failed; functional safety error (drain pump…E:24Drain pump is running but unable to remove the water; drain system blockage.E:25Drain pump unable to rotate; attempts to clear failed, or sump drain pump cover…E:26Reference cam not detected (code not used; no water switch).E:27Low supply voltage (<85 VAC).E:28Aqua sensor failed to calibrate.E:29Low supply voltage (<85 VAC); error code won't show during wash cycle.E:30Overvoltage detected.E:31Overloaded heat pump.View all 31 error codes
Service modes (31)
- Basic settings (Extra Dry / Rinse Aid / Cycle Tone)Turn dishwasher on, press and hold '>' button, then press and hold Start button
- Basic settings (Extra Dry / Rinse Aid)Turn dishwasher on, press and hold '>' button, then press and hold Start button. On LED models
- Basic settings (Extra Dry / Rinse Aid) - Digital display models (SHE3ARF)Turn dishwasher on, press and hold '>' button, then press and hold Start button
- Basic settings (Extra Dry / Rinse Aid) - LED models (SHE3AR5)Turn dishwasher on, press and hold '>' button, then press and hold Start button
- Basic settings (SHE models)1
- Basic settings (SHX Integra models)1
- Basic settings mode["Press the On/Off button to turn the dishwasher on.","While pressing and holding the 'A' button…
- Control resetWith the door closed and the dishwasher turned on, press and hold Start for five (5) seconds
- Customer service test programEnter Special programs (press and hold '>' and Delay buttons, then turn on)
- Customer service test program (error code reading)Run the customer service test program to check error codes
- Customer service test program (P1)Enter Special programs (press and hold '>' and Delay buttons, then turn dishwasher on)
- Customer service test program (SHE Evolution models)1
- Customer service test program (SHX Integra models)1
- Customer settings (codings) modePress On/Off to turn the dishwasher on. While pressing and holding button '1', press and hold Start…
- Error code programEnter Special programs (press and hold '>' and Delay buttons, then turn on)
- Error code program (P0)Enter Special programs (press and hold '>' and Delay buttons, then turn dishwasher on)
- Error code program (SHE Evolution models)1
- Error code program (SHX Integra models)1
- Reset (Cancel - drain)Press and hold Start button until Active light goes out or when display shows '0.01'.
- Sales demo (showroom) programEnter Special programs (press and hold '>' and Delay buttons, then turn on)
- Sales demo (showroom) program (P7)Enter Special programs (press and hold '>' and Delay buttons, then turn dishwasher on)
- Sales demo mode (P7)["Press the On/Off button to turn the dishwasher on.","If the dishwasher needs to be reset, turn it…
- Sales demo mode (showroom)["Press the On/Off button to turn the dishwasher on.","If the dishwasher needs to be reset, turn it…
- Sales demo program (SHE Evolution models)1
- Sales demo program (SHX Integra models)1
- Settings change mode["Press the On/Off button to turn the dishwasher on.","While pressing and holding the 'A' button…
- Special programs (codings)Press and hold '<' and '>' buttons, then turn dishwasher on
- Special programs (entry to error codes, customer service test, sales demo, etc.)Press and hold '>' and Delay buttons, then turn dishwasher on
- Special programs (service menu)Press and hold '>' and Delay buttons, then turn dishwasher on
- Special programs (SHE Evolution models)1
- Special programs (SHX Integra models)1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Bosch dishwasher models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax