Model reference
Bosch SHV7ER53UC
Dishwasher
6 documents34 error codes7 service modes
Available documentation
Service Manual
- Bosch Dishwasher SHV7ER53UC 55 Emoction Series Service Manual177 pg
- Fault Codes and Service Programmes5 pg
- Bosch Dishwasher SHV7ER53UC 55 Check Routine3 pg
- Repair Instruction - Dishwasher 800 Series Service Manual137 pg
Wiring Diagram
- Bosch Dishwasher SHV7ER53UC 55 Connection Diagram1 pg
Other
- Bosch Dishwasher SHV7ER53UC 55 Check Routine3 pg
MyPros+ Max
Diagnose your Bosch SHV7ER53UC.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (34)
CodeMeaning
E:00No error present in the appliance.E:01Communication error between the electronics (D-bus interface error).E:02Working relay for heater defective; pump control or pump switchover defective.E:03Working relay for auxiliary heater defective.E:04Ground fault at zeolite heater or safety relay heater defective; internal fault…E:05Triac for water switch motor defective; water switch is running continuously…E:06Door Hall sensor fault; wire to the Hall sensor interrupted or power module…E:07Fan defective or blocked, module on the fan defective (only on appliances with…E:08Heat exchanger valve leaky; heat pump detects too low water level in pump sump.E:09Heating circuit interrupted (resistance, supply wires, contacts of the safety…E:10Zeolite heater heating circuit interrupted (resistance/supply wires), fan…E:11NTC resistance values outside permitted range, or wire/plug interrupted (low…E:12NTC resistance values outside permitted range (auxiliary drying system).E:13Water temperature too high (>75°C); protective measure, may not be an appliance…E:14Filling fault; no impulses from flow sensor although water is detected by heat…E:15Base carrier safety switch active; appliance cannot be switched off.E:16Water supply (impulses from flow sensor) without activation of the filling…E:17Water supply rate too high according to flow sensor.E:18Water supply rate too low according to flow sensor or no water supply.E:19Reserved.E:20Circulation pump fault; resistance values of heat pump wrong or heat pump…E:21Circulation pump fault (same as E:20); resistance values of heat pump wrong or…E:22Residual water in the pump sump due to dirty filters.E:23Drain pump fault; resistance values of drain pump wrong.E:24Non-return valve leaky or draining not possible due to drain pump cover missing…E:25Drain pump blocked or drain pump cover missing from pump sump.E:26Water switch fault; permanent activation of water switch or no impulses from…E:27Continuous undervoltage (<170V); not an appliance fault.E:28AquaSensor fault; appliance not equipped with AquaSensor or calibration of…E:29Undervoltage (<170V / 190V); not an appliance faultService modes (7)
- Customer service test programmeNot explicitly detailed in the document; referenced as a test programme used for performance…
- Customer Service Test Programme (P1)["Enter Service Programme.","Press button B until P1 is displayed.","Activate by pressing button…
- Customer settings modeWith the appliance switched on, simultaneously press button A and the 'Start' button
- Demonstration Programme (P7)["Enter Service Programme.","Press button B until P7 is displayed.","Activate by pressing button C…
- Electronic button lock (childproof lock)Start the required programme, then hold down button B for approx
- Error Memory Readout (P0)["Enter Service Programme.","P0 is displayed by default upon entry.","Activate by pressing button…
- Service Programme Entry["Ensure appliance is in program selection mode (if in rinsing program, perform Reset, switch off…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Bosch dishwasher models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass