mypros+
Model reference

Electrolux ELTE7600AW0

Dryer

6 documents80 error codes8 service modes

Available documentation

Tech Sheet

  • Laundry Tower Tech Data Sheet32 pg
    Covers this model

Service Flash

  • SERVICE FLASH LNSF2518 FLD Drum Vane1 pg
    Covers this model

Tech Tip

  • Tech Tip LNTT2412 - Laundry Tower Tapping Noise1 pg
    Covers this model
  • Tech Tip LNTT2516 Dryer Door Rattling1 pg
    Covers this model
  • Blower Wheel Notches1 pg
    Covers this model
  • Tech Tip LNTT2511 Blower Wheel Socket Size_2070561 pg
    Covers this model
MyPros+ Max

Diagnose your Electrolux ELTE7600AW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (80)

CodeMeaning
11Fill time too long.13Water leak in tub or in pressure sensor.21Water not pumping out fast enough.23Drain triac error.24Drain triac error sensing.31Electronic pressure switch error.32Pressure sensor calibration problem.34Dryer35Dryer38Air trap clogged.41Dryer42Dryer43Door lock triac failure.44Door closed sensing failure.45Line door sensing failure.51Dryer52Dryer53Dryer54Dryer55Motor under speed (select models, not available on 7300 series).57High current on inverter (motor control).58High current on motor phase.59No spin signal for 3 seconds.5AHigh temperature on control due to overload (motor control).5BMotor control under voltage.5CHigh voltage experienced by motor control board.5DCommunication problem with motor control (message).5ECommunication problem from motor control (communication failure).5FMC is continuously resetting.61Dryer
View all 80 error codes
62Wash temperature too high.63Dryer64Dryer65Dryer66Heater relay problem (select models).67Dryer68Current leakage to ground on heater or wiring (select models).69Heater open (select models).6AHeater relay sensing problem (select models).71Drum water NTC failure (tub heater) (select models).72Dryer73Dryer74Dryer83Wrong selector reading.84Recirculation pump triac sensing failure which stops the cycle (select models).85Recirculation pump triac alarm which stops the cycle (select models).86Incorrect UI selection table.87User interface micro-controller fault.88Concentrated wash pump triac alarm (select models).91User interface protocol incongruence error.92Dryer93Console or main board control problem (incompatible machine configuration).94Main board control problem (incompatible cycle configuration).97Console or main board control problem (incompatible cycle configuration).98Incompatible motor control/main board.9CDryer9ETouch sensor on user interface not responding.B1Frequency of power out of limits.B2Supply voltage too high (incoming voltage).B3Supply voltage too high (incoming voltage).B4DryerBDDryerBEControl relay fault.BFControl relay sense fault.C1Flow meter is running when no valves are driven (select models).F1DryerF2Too much soap or wrong type.F3DryerF4Flow meter is not running when valves are driven (select models).F5Load unbalanced.F6Control reset.F9Hot valve warningFBLoad entrapment error.H1Frequency of power out of limits.H2DryerH3Supply voltage too high (incoming voltage).H4DryerHADryerHEControl relay fault.HFControl relay sense fault.

Service modes (8)

  • Dryer Demo Mode["Press dryer button and look for console light up.","Cycle to the 6th position using the cycle…
  • Dryer Diagnostic Mode["Press dryer button and look for console to light up.","Use cycle selection buttons to set cycle…
  • Dryer Factory Default Reset["Press dryer button and look for console light up.","Wait at least 10 seconds, then simultaneously…
  • Dryer Recall Last Error Code["Press dryer button and look for console light up.","Wait at least 10 seconds, then simultaneously…
  • Washer Demo Mode["Press washer button and look for console light up.","Cycle to the 6th position using the cycle…
  • Washer Diagnostic Mode["Press washer button to turn machine on.","Use cycle selection buttons to set cycle to…
  • Washer Factory Default Reset["Press washer button and look for console light up.","Wait at least 10 seconds, then…
  • Washer Recall Last Error Code["Press washer button and look for console light up.","Wait at least 10 seconds, then…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Electrolux dryer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax