mypros+
Error code reference

Electrolux Dryer Error Code F9

Door Latch Supervisory (Door Latched)

Electrolux codesElectrolux dryer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F9 error code actually means

Your Electrolux dryer is showing an F9 error because it detected a problem with the door latch system and stopped the cycle as a safety precaution. The dryer could not confirm that the door was properly closed and secured during operation. Try pressing the CANCEL button after opening the door, but if the door feels stuck or very hot, unplug the dryer first and wait for it to cool down before opening it.

Diagnostic procedure

The full F9 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Unlatch the door (if not locked) and press CANCEL key to reset. If door is locked (temperature >400°F), power must be removed until the oven door can be unlatched.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F9 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F9

Ranked by how often they cause this code
  1. 1Faulty Door Latch Switch
  2. 2Misaligned Door Striker or Latch Assembly
  3. 3Damaged or Loose Wiring in the Door Latch Circuit
  4. 4Failed Control Board
  5. 5Temporary Supervisory Logic Glitch

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F9

What does F9 mean on a Electrolux dryer?
The F9 code indicates a Door Latch Supervisory failure. The dryer's control system monitors the door latch status continuously, and if the supervisory logic detects an inconsistency for a 2-second sample period while the door is latched, it triggers this fault. The alarm sounds and the control resets to a non-operational mode as a safety measure.
Is the F9 error on my Electrolux dryer a safety concern?
Yes, this error is safety-related. The dryer stops operation automatically to prevent unsafe conditions when the door latch supervisory system fails. If the door feels stuck or the unit is very hot, do not attempt to force the door open. Disconnect power and allow the appliance to cool before accessing the door or any internal components.
How much does it cost to repair an F9 error on an Electrolux dryer?
Repair costs vary depending on the root cause. Replacing a door latch switch typically costs between $20 and $80 for the part, while a new control board can range from $100 to $300 or more. Adding professional labor, total repair costs can range from $75 to $400 depending on the component involved and local service rates.
How do I fix the F9 error on my Electrolux dryer?
Start by unlatching the door if it is not locked, then press the CANCEL key to reset the control. If the door is locked due to high internal temperatures above 400 degrees Fahrenheit, disconnect power to the dryer and wait until it cools before opening the door. If the code returns after resetting, inspect the door latch switch, wiring connections, and latch alignment for faults.
Will resetting my Electrolux dryer clear the F9 error code?
A reset may clear the code if the fault was caused by a temporary logic glitch or a power fluctuation. Unlatch the door and press CANCEL, or disconnect power for several minutes before restarting. However, if the underlying cause is a failed door latch switch, damaged wiring, or a faulty control board, the code will return and those components will need to be inspected and repaired.

Related Electrolux dryer error codes

All Electrolux dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass