mypros+
Model reference

Frigidaire LTF6000ES0

Washer

6 documents49 error codes8 service modes

Available documentation

Tech Sheet

  • Washer Tech Data Sheet16 pg
    Covers this model

Service Manual

  • Technical Service Manual 2009 3 5 Cu Ft Affinity Front Load 6000 and 7000 Series74 pg
    Covers this model

Service Flash

  • Service Flash LN063 Affinity Washers Enter Continuous Cycle Loop, Error Message Displayed1 pg
    Covers this model

Training

  • Technical Service Manual 2006 Technical Training Manual139 pg
    Covers this model

Quick Reference

  • Washer Operating Instructions6 pg
    Covers this model
  • Frigidaire Washer Consumer Error Codes LTF6000ES0 1346045002 pg
    Covers this model
MyPros+ Max

Diagnose your Frigidaire LTF6000ES0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (49)

CodeMeaning
E11Fill time too long.E13Water leak in tub or air leak in air bell.E21Water not pumping out fast enough.E23Drain pump relay on control board failed or wire off pump.E24Drain pump relay on control board failed or wire off pump.E31Pressure sensor not communicating with control board.E35Pressure sensor indicates water overfill.E36Control board problem.E41Control board thinks the door switch is open.E43Control board problem.E44Control board problem.E45Control board problem.E46Control board problem.E47Board thinks the door PTC circuit is open in spin.E48Board thinks the door PTC circuit is closed.E52Bad signal from tacho generator.E56High motor current.E57High current on inverter.E58High current on motor phase.E59No tacho signal for 3 seconds.E5AHigh temperature on heat sink caused by overloading.E5BHigh temperature on heat sink.E5CHigh temperature on heat sink.E5DCommunication problem between control board and speed control board.E5ECommunication problem between control board and speed control board.E5FCommunication problem between control board and speed control board.E66Heating element relay failure.E67Input voltage on microprocessor incorrect.E68Current leakage to ground on heater or fuse opened.E71Wash NTC failure (tub heater).
View all 49 error codes
E74Wash temperature does not increase.E75Water temperature sensor circuit failure.E76NTC temperature for the cold water valve over the limits.E82Console control problem.E83Console control problem.E91Communication error between UI board and control board.E93Console control problem.E94Console control problem.E95Communication error.E97Console control problem.E98Console control problem.EB1Incoming power frequency out of limits.EB2Incoming line voltage above 130 VAC.EB3Incoming line voltage below 90 VAC.EBEConsole control problem.EBFConsole control problem.EF1Clogged drain pump.EF2Too much soap.EF5NTC temperature for the hot water valve over the limits.

Service modes (8)

  • Clear Stored Error Code["Turn the Program Knob to the start position, Spin Only.","Press Start/Pause to start the cycle…
  • clear_error_code["Turn the Program Knob to start position (Spin Only).","Press START/PAUSE to start the cycle and…
  • control_lock["Press Options and Select at the same time and hold for 10 seconds until 'LOC' is displayed…
  • diagnostic["Turn Program Knob to the start position (Spin Only).","Press START/PAUSE to start the cycle and…
  • Diagnostic Test["Turn the Program Knob to the start position, Spin Only.","Press Start/Pause to start the cycle…
  • Read Error Codes["Wake the washer by pressing any button.","Wait 5 seconds.","Press and HOLD the Start/Pause and…
  • read_error_codes["Wake the washer by pressing any button.","Wait 5 seconds.","Press and hold the START/PAUSE and…
  • reset_factory_settings["Press Start/Pause and Select at the same time and hold until a signal sounds."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Frigidaire washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass