mypros+
Model reference

Whirlpool YWFE745H0FS3

Range

5 documents33 error codes17 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11503313 - Rev A2 pg
    Covers this model
  • Fiche technique - Tech Sheet W107232148 pg
    Covers this model
  • Tech Sheet - W10723213 - Rev A8 pg
    Covers this model

Service Manual

  • Tech Manual16 pg
    Covers this model
  • Technical Manual - Cooking Surface Temperature Limits12 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool YWFE745H0FS3.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (33)

CodeMeaning
F1EEPROM communication error (E0), sensor out of range (E5), PCB thermistor open…F1 E0EEPROM communication error.F1 E5Sensor out of range.F1 E7Circuit board thermistor open or short-circuited.F1E0EEPROM communication error within the MRC control.F1E5Sensor out of range (MRC control failure).F1E7PCB thermistor open or shorted.F2Keypad issueF2 E0Keypad disconnected.F2 E1Key stuck.F2 E2Cancel key error.F2E0Keypad disconnected from MRC control.F2E1Stuck key detected on keypad.F2E2Cancel key error.F3Temperature sensor faultF3 E0Main oven sensor open or short-circuited.F3 E2Warming drawer sensor open or short-circuited.F3E0Main oven temperature sensor open or shorted.F3E2Warming drawer temperature sensor open or shorted.F5Door-related faultF5 E0Door and switch mismatch (clean modeF5 E1Door latch not functional (clean modeF5E0Door and switches do not agree (Clean modeF5E1Door latch not operating (Clean modeF6Over temperature conditionF6 E1Bake modeF6 E2Clean modeF6 E3Warming drawerF6E1Over temperature during cook mode.F6E2Over temperature during clean mode.
View all 33 error codes
F6E3Over temperature in warming drawer.F9Mis-wired house or range (E0).F9E0Mis-wired house or range electrical connection.

Service modes (17)

  • Auto TestFrom diagnostic mode (CANCEL>CANCEL>START), press up arrow, '+', or '3' to scroll to 'AUTO TEST'…
  • CONTROL RESETFrom diagnostic mode, scroll to step 6 (CONTROL RESET).
  • Diagnostics Mode (Auto Test)["Press CANCEL","Press CANCEL","Press START (display shows 'TEST ON' with cavity temperature and…
  • Diagnostics Mode (Service Mode Entry)Press CANCEL > CANCEL > START
  • DISPLAYFrom diagnostic mode, scroll to step 5 (DISPLAY).
  • ENG MODE["Press CANCEL>CANCEL>START to enter Service Mode","Scroll to ENG MODE (Service Mode 2)","Press…
  • ENG MODE (Engineering Mode)From diagnostic mode, scroll to step 2 (ENG MODE)
  • FAULTSFrom diagnostic mode, scroll to step 7 (FAULTS).
  • MRC Control Module Diagnostic ModePress CANCEL, then CANCEL again, then START
  • RELAY USAGEFrom diagnostic mode, scroll to step 8 (RELAY USAGE).
  • Temperature Adjustment["Press OVEN LIGHT for 5 seconds (current offset or 0° is shown in display)","Press Temp/Time or…
  • TEST MODE["Press CANCEL>CANCEL>START to enter Service Mode","Scroll to TEST MODE (Service Mode 3)","Perform…
  • TEST MODE (Relay Control)From diagnostic mode, scroll to step 3 (TEST MODE)
  • TEST ON (Relay Checks)["Press CANCEL","Press CANCEL","Press START","Display shows 'TEST ON'
  • TEST ON (Relay Control)Entered immediately upon entering diagnostic mode (CANCEL>CANCEL>START)
  • USAGEFrom diagnostic mode, scroll to step 1 (USAGE) using up arrow, '+', or '3'.
  • VERSIONFrom diagnostic mode, scroll to step 4 (VERSION).

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass