Model reference

Wolf ICBDF304-LP

Name: Wolf ICBDF304-LP
Brand: Wolf

Range

7 documents88 error codes16 service modes

Available documentation

Service Manual

Wolf Legacy DF Ranges: All Serials — Service Manual88 pg
Covers this model
Wolf Service Manual: Legacy Dual Fuel — Service Manual115 pg
Covers this model

Parts Manual

Wolf ICB Legacy Dual Fuel Range Enhancement: After Serial 17312500 — Parts Manual59 pg
Covers this model
Wolf ICB Legacy Dual Fuel Range: Prior to Serial 17312499 — Parts Manual43 pg
Covers this model
Wolf Legacy Dual Fuel Enhancements (826424): After Serial 18180000 — Parts Manual74 pg
Covers this model
Wolf Legacy Dual Fuel -3: Serials 16000000 to 18179999 — Parts Manual68 pg
Covers this model
Wolf Original Legacy Dual Fuel: Prior to Serial 16000000 — Parts Manual68 pg
Covers this model

MyPros+ Max

Diagnose your Wolf ICBDF304-LP.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Wolf Range

01 on my Wolf ICBDF304-LP

M+

Door Lock or Unlock Switches not sensed

From Service Manual 396453, p.25:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure door lock assembly resistance across PTC terminals. Expected: ~200 ohms cold.

3.Inspect strike and latch alignment. A misaligned strike prevents the switch stack from closing.

Part W10810403

Door lock assembly

Error codes (88)

CodeMeaning

01Door Lock or Unlock Switches not sensed within 60 seconds while driving the…01-00RTD Open 01-01RTD Shorted 02Over temperature occurs when the oven reaches a temperature of 630°F for an…02-00Meat Probe Short 03Open circuit detected on RTD Oven Sensor.03-00No Inner Bake element detected.03-01No Outer Bake element detected.03-02No Broil element detected.03-03No Left Convection element detected.03-04No Right Convection element detected.03-05No MDL (Motor Door Lock) detected.03-06No Left Convection Fan detected.03-07No Right Convection Fan detected.03-08No Cooling Fan detected.03-09No Oven Light detected.04Shorted circuit detected on the RTD Sensor.04-00Lock inputs invalid.04-01Lock/Door inputs invalid for Clean.04-02MDL run timeout.05-00TCO (Thermal Cutoff) detected as open.06-00Brownout error.07SPI Communication lost from ECH to the Control Board as reported by Control…07-00Inner Bake relay shorted.07-01Outer Bake relay shorted.07-02Broil relay shorted.07-03Left Convection relay shorted.07-04Right Convection relay shorted.07-05MDL relay shorted.07-06Left Convection Fan triac shorted.

View all 88 error codes

07-07Right Convection Fan triac shorted.07-08Cooling Fan triac shorted.07-09Oven Light relay shorted.07-10DLB1 shorted.07-11DLB2 shorted.07-12Aux DLB shorted.07-13Inner Bake relay open.07-14Outer Bake relay open.07-15Broil relay open.07-16Left Convection relay open.07-17Right Convection relay open.07-18MDL relay open.07-19Left Convection Fan triac open.07-20Right Convection Fan triac open.07-21Cooling Fan triac open.07-22Oven Light relay open.07-23DLB1 relay or TCO open.07-24DLB2 relay open.07-25Aux DLB open.07-26RTD Circuitry error.07-27RM EE checksum error.07-28HIV SPI communication error detected by RM control.07-29HIV SPI communication error detected by HV-micro.07-30HIV micro feedback error.07-31RM LOV fuse error.07-32RM HIV fuse error.07-33HSWD active, should be inactive.07-34HSWD inactive, should be active.07-35RM Ambient Thermistor open error.07-36RM Ambient Thermistor shorted error.07-37RM Line Voltage A/D error.07-38MDL circuitry error.07-39RM FMEA circuitry error.08EEPROM checksum is incorrect, checked at power up.08-00Keypad circuit error.08-01Keypad communications error detected by the UIM.08-02Keypad communications error detected by the Keypad.08-03Keypad FMEA error.08-04Keypad EE CRC error.08-05Keypad mains sync error.09Meat probe being sensed as shorted.09-00UIM EE checksum error.09-01UIM configuration data CRC error.09-02UIM fuse error.09-03UIM ambient thermistor open error.09-04UIM ambient thermistor shorted error.09-05LCD module error.0BAnalog to Digital error during calibration phase.0CCommunication lost with oven controller.0EPower relay shorted, sensed as closed when should be open 10-00Communications error detected by the UIM.10-01Communications error detected by the RM (Relay Module).11-00Overtemp error 11-01Overtemp error 12-00RM Ambient overtemp error.13-00UIM Ambient overtemp error.14-00Self-clean rate-of-rise error.15-00LPM (Low Power Module) error.

Service modes (16)

Diagnostic Mode1
Diagnostic Mode - Element Testing1
Diagnostic Mode - Fan and Motor Testing1. Enter Diagnostic Mode. 2. Turn oven control knob bezel or press key on ECH
Diagnostic Mode - Fans and Motors Testing1. Enter Diagnostic Mode. 2. Turn oven control knob bezel or press key on ECH to activate specific…
Diagnostic Mode - Probe Testing1
Diagnostic Mode - RTD Testing1
Element Testing (within Diagnostic Mode)1. Enter Diagnostic Mode. 2. Turn the oven control knob bezel to the appropriate cooking mode…
Fan and Motor Testing (within Diagnostic Mode)1. Enter Diagnostic Mode. 2. Turn oven control knob bezel or press key on ECH to activate specific…
Field Option Mode - 12/24 Hour Clock1
Field Option Mode - 12hr/24hr Clock Change1
Field Option Mode - Fahrenheit to Celsius1
Field Option Mode - Fahrenheit/Celsius Change1
Field Option Mode - User Preference Offset (UPO)1
Probe Testing (within Diagnostic Mode)1
RTD Testing (within Diagnostic Mode)1
Three Field Option Modes1. Press and hold CLOCK key for 5 seconds. 2. To change 12hr/24hr clock

Full entry steps, exit procedures, and test sequences are available in Max.

Related Wolf range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass