Model reference
Electrolux EWM2000
Washer
2 documents36 error codes10 service modes
Available documentation
Service Manual
- Diagnostics Guide to EWM2000 Electronic Control74 pg
Other
- ewm200058 pg
MyPros+ Max
Diagnose your Electrolux EWM2000.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (36)
CodeMeaning
E11Problems with water fill in wash phaseE12Problems filling water during drying cycle phaseE21Problems during draining phaseE22Difficulties in draining water during drying phase or drying condenser blocked.E31Analogic (electronic) pressure switch circuit faultyE32Incorrect calibration of analogic (electronic) pressure switchE33Incongruency between level of analogic (electronic) pressure switch and level…E34Incongruency between level of electronic pressure switch and level of…E35Water level too highE36Sensing circuit of anti-boiling pressure switch 1 on the electronic board is…E37Sensing circuit of anti-boiling pressure switch 2 on the electronic board is…E38Pressure chamber blockedE41The machine is not able to lock the doorE42The door is felt open during the cycle or remains closed at the end of the cycleE43TRIAC which powers the door interlock faultyE44Sensing circuit of door delay interlock on the electronic board is not working…E45Sensing circuit of door delay interlock triac on the electronic board is not…E51TRIAC which powers the motor is short-circuited or has dispersion.E52No signal from tachometric generator in the motor.E53Sensing circuit of motor TRIAC on the electronic board is not working properly.E54Relays (motor) contacts on the main board are not working properlyE61Insufficient heating measured by the main board during washing cycleE62Overheating during washing cycleE63Insufficient heating measured by the main board during drying cycle.E64Overheating during drying cycleE66Faulty relay that gives power to the heating elementE71Washing NTC sensor failureE72Drying NTC sensor on condenser failureE73Drying NTC sensor on duct near heating element failureE84Sensing circuit on circulation pump triac on the electronic board is not…Service modes (10)
- Configuration Mode - AEG (Table 5)["First enter the diagnostics system.","Turn the programme selector clockwise to the last position…
- Configuration Mode - DELTA3/NEAT (Table 3)["First enter the diagnostics system.","Press FABRICS (1) or TEMPERATURE (2) buttons until LED L10…
- Configuration Mode - FULL SMD with ON/OFF button (Table 1)["First enter the diagnostics system.","Turn the programme selector one position counter-clockwise…
- Configuration Mode - FULL SMD with ON/OFF switch on selector (Table 2)["First enter the diagnostics system.","Turn the programme selector clockwise to the last position…
- Configuration Mode - INPUT (Table 4)["First enter the diagnostics system.","Press FABRICS (1) or TEMPERATURE (2) buttons until LED L14…
- Diagnostic Mode - AEG (Table 5)["Switch off the appliance and turn the programme selector knob to OFF/RESET.","Press button 1 and…
- Diagnostic Mode - DELTA3/NEAT (Table 3)["Press the SKIP/RESET button to cancel the previously selected programme and switch off the…
- Diagnostic Mode - FULL SMD with ON/OFF button (Table 1)["Switch off the appliance and turn the programme selector knob to RESET.","Press the START/PAUSE…
- Diagnostic Mode - FULL SMD with ON/OFF switch on programme selector (Table 2)["Switch off the appliance.","Press the START/PAUSE button (8) together with one of the other…
- Diagnostic Mode - INPUT (Table 4)["Switch off the appliance.","Press the SPIN button (3) together with button no
Full entry steps, exit procedures, and test sequences are available in Max.
Related Electrolux washer models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax