mypros+
Model reference

Maytag MHN30PDAXW0

Washer

5 documents37 error codes29 service modes

Available documentation

Service Manual

  • Service Manual - Maytag Model 30 Commercial Front Loading Washers104 pg
    Covers this model

Tech Sheet

  • Tech Sheet - W10311070 - Rev B (FR)16 pg
    Covers this model
  • Tech Sheet - W10311068 - Rev B16 pg
    Covers this model

Installation Guide

  • Installation Instructions32 pg
    Covers this model

Other

  • service pointer mhn33 ui programmin fc4f709f2de031 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MHN30PDAXW0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (37)

CodeMeaning
d10Overheating of motord11MCU errord12Door switch errord13Coin 2 errord14Pump disconnectedd15Load detected in washer during Washer Cleanout Cycle.d16Generation 2 debit card reader errord17Door lock errord19Door unlock errord20Communication failure between CCU and MCU.d21Overflow conditiond23Communication failure between CCU and UI.d24Temperature sensor errord3UI failured4Tachometer errord5Coin 1 errord6CCU errord7MCU errord8No water detected entering washer.d9Low voltage detection errorF01CCU errorF11MCU errorF20No water detected entering washerF21Long drainF22Door lock errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between CCU and MCU.
View all 37 error codes
F29Door unlock errorF31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F70Communication failure between CCU and User Interface (UI).F73UI failureF74UI failure

Service modes (29)

  • Code Display Mode["PD Models
  • Cycle Credit["Enter Flashing Mode (entire display flashing).","Press the PERM
  • Diagnostic Mode (Blink Mode)["First access Setup mode (see Setup/Configuration Mode entry).","Press QUICK CYCLE button for 1…
  • Diagnostic Mode (Washer Diagnostic Mode)["Enter 'Start Operating Set-Up' mode first.","For PD Models
  • Flashing Mode["PD Models
  • Free Cycle Credit["Enter Blink Mode (entire display is blinking).","Press the PERM
  • Help Mode (dAS mode)["Open the service door or insert a manual diagnostic card.","dAS message appears on the…
  • Help Mode (PD models)["Open the service door.","Press DELICATES AND KNITS until display shows 2.XX.","Press PERM
  • Manual Overview Test["Enter Flashing Mode (diagnostic mode with entire display flashing).","Press the WHITES button."]
  • Manual Overview Test Program["Enter Blink Mode (entire display is blinking).","Press the WHITES button."]
  • Quick Drain and Spin["Enter Flashing Mode (diagnostic mode with entire display flashing).","Press the COLORS button."]
  • Quick Drain and Spin Program["Enter Blink Mode (entire display is blinking).","Press the COLORS button."]
  • Quick Overview Test["Enter Flashing Mode (diagnostic mode with entire display flashing).","Press the DELICATES AND…
  • Quick Overview Test Program["Enter Blink Mode (entire display is blinking).","Press the DELICATES AND KNITS button."]
  • Quick Spin Cycle["Enter Flashing Mode (entire display flashing).","Press the COLORS button."]
  • Service Access Code["Only functions on washers set up for 0 vend price without any Special Pricing, and Coin/Debit…
  • Service Access Code (PR models configured as PN without key switch)["Using only the three bottom buttons (numbered 1, 2, 3 from left to right):","1. Press button 2…
  • Service Access Code (PR Models set up as PN)["Door must be opened if washer is not in failure mode.","Using only the three bottom buttons…
  • Service Access Code Entry["Only functions on washers set up for 0 vend price without any Special Pricing set-up, and…
  • Set-Up Mode (PD Models)["Use service key to remove service access door.","Lifting the service access door engages the…
  • Set-Up Mode (PR Models via AA1)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Set-Up Mode (PR Models)["Unplug washer or disconnect power.","Open console, remove and retain plug on AA1, close…
  • Setup/Configuration Mode (PD models)["Insert key into service door access.","Turn and lift to remove the service access door.","Use the…
  • Setup/Configuration Mode (PR models via AA1 connector)["Unplug the washer or disconnect power.","Open the console and disconnect connector AA1.","Close…
  • Washer Clean Cycle["Enter Blink Mode (entire display is blinking).","Press the BRIGHTS button."]
  • Washer Cleanout Cycle["Enter Flashing Mode (entire display flashing).","Press the BRIGHTS button."]
  • Washer Cleanout Cycle (from diagnostic mode)["Enter Flashing Mode (diagnostic mode with entire display flashing).","Press the BRIGHTS button."]
  • Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (enter set-up mode).","Press and hold the QUICK CYCLE button…
  • Washer Diagnostic Mode (Flashing Mode)["First enter 'Start Operating Set-Up' (set-up mode).","Press and hold the QUICK CYCLE button for 1…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass