Model reference

Speed Queen SWFA61WN

Name: Speed Queen SWFA61WN
Brand: Speed Queen

Washer

2 documents49 error codes8 service modes

Available documentation

Service Manual

Preventative Maintenance - Frontload Washer16 pg
Covers this model
Programming NetMaster Frontload Washer143 pg
Covers this model

MyPros+ Max

Diagnose your Speed Queen SWFA61WN.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Speed Queen Washer

Alrm on my Speed Queen SWFA61WN

M+

Break-in alarm error triggered by

From Service Manual 426838, p.50:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure door lock assembly resistance across PTC terminals. Expected: ~200 ohms cold.

3.Inspect strike and latch alignment. A misaligned strike prevents the switch stack from closing.

Part W10810403

Door lock assembly

Error codes (49)

CodeMeaning

AlrmBreak-in alarm error triggered by service door or coin vault switch.doorDoor open indicator; door is not closed during an active cycle.E:dFDrive failure; motor unplugged, motor failure, tachometer circuit open, or drum…E:dLDoor lock error; door does not lock within 15 seconds of closing or 3 minutes…E:doDoor opened during a running cycle; control detects door open and door locked…E:FLFill error; pressure switch fails to open in 30 minutes in any fill agitate…E:SPSPI communications error; master control cannot communicate with motor control.E:UbUnbalance error; unable to balance load.EC:00General card reader communication error.EC:02Card reader timeout error during communication.EC:03Invalid command code from card reader due to incorrect machine type.EC:05Invalid or out-of-range data from card reader due to incorrect machine type.EC:06Invalid data code from card reader due to incorrect machine type.EC:09Corrupted data error during card reader communication.EC:0AInvalid machine type detected during card reader communication.EC:19No card reader communication detected.EC:20Unreadable card inserted into reader due to faulty card or dirty contact.EC:21Security ID mismatch on inserted card.EC:22Site code mismatch on inserted card.EC:23Card maximum value exceeded; value on card is over the programmed maximum.EC:24Insufficient memory on card; card memory is full.EC:25Card reader malfunction detected.EC:26Card write error during transaction.EC:27Diagnostic test card write failure indicating faulty card reader.EC:28Diagnostic test card read failure indicating faulty card reader.EC:29Diagnostic test memory test failure indicating faulty card reader.EC:2ADiagnostic test card interface failure indicating faulty card reader.EC:2bDiagnostic test flash checksum failure indicating faulty card reader.EC:2CBiberon or non-biberon device failure indicating faulty card reader.EC:2dFirmware update failed but existing software is intact.

View all 49 error codes

EC:2EFirmware update failed and software is not intact.EC:2FFirmware updated but software is not intact, indicating faulty firmware in…EC:30Card reader timeout error.EC:31Hotlisted card inserted into reader; control will destroy card.EC:50Loyalty purse read error on card.EC:56Loyalty purse write error on card.EI:01Infra-red transmission failure during Micro-Wand communication.EI:02Device timeout during Micro-Wand communication.EI:03Invalid command code received during infra-red communication due to incorrect…EI:04Expecting upload request during Micro-Wand communication.EI:05Invalid or out-of-range data received during infra-red communication due to…EI:06Invalid data code received during infra-red communication due to incorrect…EI:07Error writing to the real-time clock, indicating a control failure.EI:08Error writing to EEPROM, indicating a control failure.EI:09CRC-16 error during Micro-Wand communication.EI:0AInvalid machine type detected during infra-red communication.EI:0FInvalid wakeup signal or infra-red communication is disabled.ErrCoin error; invalid coin pulse or inoperative coin sensor.OFFBreak-in alarm shutdown error triggered by service door or coin vault switch.

Service modes (8)

Audit Mode (AudT)["1
Clear Vend["1
Diagnostic Mode (dIAg)["1
Manual Mode["1. Ensure washer is in Ready Mode. If in active cycle, use Rapid Advance to complete. If coins…
Manual Reset (rSET)["1
Programming Mode (PrOg)["1
Rapid Advance Mode (rAPd)["From Ready Mode
Sales Floor Mode (SHOW)["1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Speed Queen washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass