mypros+
Model reference

Whirlpool GS440LEMB5

Range

9 documents47 error codes11 service modes

Available documentation

Tech Sheet

  • Tech Sheet - 97580874 pg
    Covers this model

Service Manual

  • TECHNICAL EDUCATION JOB AID 4317368 KAC-40 FAILURE CODES AND WIRING DIAGRAMS for WHIRLPOOL AND KITCHENAID SLIDE-IN & FREESTANDING GAS & ELECTRIC RANGES80 pg
    Covers this model
  • Whirlpool Gas Range Direct Spark Ignition System29 pg
    Covers this model
  • Job Aid - 30″ Freestanding Self-Cleaning Gas Range68 pg
    Covers this model
  • 30″ Freestanding Self-Cleaning Gas Range68 pg
    Covers this model
  • Whirlpool Gas Range Direct Spark Ignition System KR-2829 pg
    Covers this model

Service Flash

  • Technical Service Pointer - Gas Freestanding Ranges with Direct Spark Ignition (DSI) Control18 pg
    Covers this model

Installation Guide

  • Installation Instructions32 pg
    Covers this model
  • Instruction Sheet2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool GS440LEMB5.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (47)

CodeMeaning
F0 E0No failure (default state).F1 E0EEPROM communication error (Tulsa/Celaya); Internal error (Oxford).F1 E1EEPROM checksum error (Tulsa/Celaya); Internal error (Oxford).F1 E2UL A/D error (Tulsa/Celaya); Internal error (Oxford).F1 E3Internal error (Oxford).F1 E4Model ID error (Tulsa/Celaya); Internal error (Oxford).F1 E5Internal error (Oxford)F1 E6Latch signal mismatch error (Tulsa/Celaya); Internal error (Oxford)F1 E7Internal error (Oxford)F1 E8Internal error (Oxford)F1 E9Internal error (Oxford)F1E0EEPROM communications errorF1E1EEPROM checksum failureF1E2UL A/D error(s)F2 E0Shorted keypad / stuck key.F2 E1Keypad disconnect / keypad disconnected.F2E0Shorted keyF2E1Keytail unpluggedF3 E0Top oven sensor open (main sensor open).F3 E1Top oven sensor shorted (main sensor shorted).F3 E2Meat probe shorted (Tulsa/CelayaF3 E3BAKE range over temperature (Tulsa/Celaya); Bottom oven sensor shorted is F3 E3…F3 E4Bottom oven sensor open (Oxford); CLEAN range over temperature (Tulsa/Celaya).F3 E5Lower oven sensor shorted (bottom sensor short).F3 E6Warming drawer sensor open (WD sensor open).F3 E7Warming drawer sensor shorted (WD sensor shorted).F3E0Oven sensor openedF3E1Oven sensor shortedF3E2BAKE/BROIL range over temperatureF3E3CLEAN range over temperature
View all 47 error codes
F4 E2Over temperature during cook cycle (temperature runaway error).F4 E3Over temperature during clean cycle (temperature runaway error).F4 E7Over temperature cavity 2 (temperature runaway error in second cavity).F5Door lock error during Clean (3-digit display / knob control).F5 E0Door and latch switches do not agree (door latch mismatch).F5 E1Latch or latch switch failure / no operating latch / latch not operating.F5 E2Door switch fault.F5 E4Latch switch fault.F5 E6Centertap voltage failure (Tulsa/Celaya).F5 E7Unlock door error / cannot unlock door.F5E0Door and switches do not agreeF5E1Door latch not operatingF5E2Latch error during CLEANF6 E4Lost communication between power board and display board.F6 E5Cancel key error.F8 E0N/A (no likely failure condition described).PFPower failure (not a failure mode, informational only).

Service modes (11)

  • KitchenAid EZ373 & 520 Test ModeAvailable for first 60 seconds after power up. Press
  • KitchenAid GOC Clock Manual DiagnosticsWithin 120 seconds of power up
  • Last error code recallPress and hold CANCEL/OFF key for 5 seconds
  • Oxford GOC Clock Manual DiagnosticsWithin 120 seconds of power up
  • Temperature calibration (temperature knob control)Press and hold CLOCK pad for 5 seconds
  • Temperature calibration (touch pad control)Press and hold BAKE pad for 5 seconds
  • Whirlpool EZ175 & 176 Self-Diagnostic Test ModeAvailable for first 60 seconds after power up. 1) Simultaneously press BAKE and CLOCK. 2) Display…
  • Whirlpool EZ300 Self-Diagnostic Test ModeAvailable for first 60 seconds after power up. 1) Sequentially press
  • Whirlpool EZ354, 357, 358, & 410 Test ModeAvailable for first 60 seconds after power up. Press
  • Whirlpool EZ625 Diagnostic Test1) Disconnect power for at least 15 seconds, then reconnect. 2) Within one minute of power up, press
  • Whirlpool GOC Clock Manual DiagnosticsWithin 120 seconds of power up

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass