Model reference

Bosch 58300000233202

Dishwasher

2 documents56 error codes7 service modes

Available documentation

Service Manual

Failure storage and Customer Service programs2 pg
Covers this model
Repair manual - Dishwasher109 pg
Covers this model

MyPros+ Max

Diagnose your Bosch 58300000233202.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (56)

CodeMeaning

E:0000No error E:01Faulty pump relay or low voltage/excessive voltage drop causing pump failure.E:0100Internal fault power module E:0103Power module defect (internal pump control)E:0105Ground fault at Zeolite heater or relay for Zeolite heater defective E:0106Ground fault at water heater E:0107Temperature monitoring E:0108D-Bus power limit exceeded E:02Faulty heater relay E:04Faulty safety heater relay or faulty heater E:05Faulty water switch relay E:06Door ajar, not properly latched, or door latch Hall sensor not detected.E:08Heat pump detects low water level E:09Faulty/open-circuited heater circuit E:11Heat pump NTC resistances out of range or NTC's show different values.E:13Incoming water too hot (>75°C / 167°F).E:15Water in base activated float switch E:17Inlet water flow rate too high E:18Inlet water flow rate too low or faulty water inlet valve E:20Faulty heat pump motor winding or disconnected heat pump harness.E:2012Heating circuit interrupted (resistance, supply wires, contacts of the safety…E:2030Heating element is calcified E:2040Wire or plug interrupted E:2050Safety relay heater defective E:2060NTC resistance values are outside permitted range E:21Heat pump is blocked or clogged.E:2120Zeolite heater heating circuit interrupted (resistance/supply wires)E:2130Heating fault E:22Water remaining in sump E:23Faulty drain pump motor winding or disconnected drain pump harness.

View all 56 error codes

E:24Drain obstruction E:25Missing or loose drain pump cover, or drain pump blocked E:26Faulty water switch, water switch motor, or water switch harness.E:27Low supply voltage continuously <85 VAC E:28Aqua sensor not properly calibrated E:29Low supply voltage (<85 VAC)E:30High supply voltage (>140 VAC)E:3000Filling fault E:3100Filling fault E:32Overloaded drain pump due to kinked or clogged drain hose (may not show during…E:3200No water supply at start of program or water supply flow is too low E:3300Water supply flow is too high E:3400Water supply (impulses from flow sensor) without activation of the filling…E:6001Circulation pump fault E:6002Drain pump fault E:6101Open circuit to drain pump or resistance values of drain pump are wrong E:6102Drain pump is blocked or drain pump cover in sump is missing/loose E:6103Non-return valve letting water by or draining is not possible, drain pump cover…E:6900Dispenser or heat exchanger valve fault E:6A00Water switch fault E:8000Door Hall sensor fault E:8101Aquasensor fault E:9000Under/over voltage error E:9001Undervoltage fault E:9010Over voltage error (>142V)E:9240Zeolite fan defective or blocked, open circuit to Zeolite fan, or resistance…

Service modes (7)

Customer Service Program (P1)["Enter the Special Functions Menu first.","While in the Special Functions Menu, press the 'B4' key…
Customer settings (codings) mode1
Dishwasher resetPress and hold Start/Reset for at least 3 seconds to reset dishwasher.
Failure Storage["Enter the Special Functions Menu first.","Press 'B4' until the following is displayed
Power module reset - Method 11
Power module reset - Method 21
Special Functions Menu["Power off dishwasher by pressing 'On/Off' button.","Press and hold 'B4' + 'Start'…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Bosch dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax