mypros+
Model reference

Maytag MHWE500VW10

Washer

9 documents64 error codes13 service modes

Available documentation

Tech Sheet

  • Tech Sheet W1013349016 pg
    Covers this model
  • Whirlpool Washer WFW9600TW01 Tech Sheet16 pg
    Covers this model
  • Tech Sheet W10207733 Maytag Epic Z Washer MHWZ600TW0116 pg
    Covers this model

Service Manual

  • Epic Front-Loading Automatic Washer Technical Education Job Aid88 pg
    Covers this model
  • Epic Front-Loading Automatic Washer88 pg
    Covers this model
  • Maytag Epic with Oxi/prewash Option / Maytag Epic Z2 pg
    Covers this model
  • Technical Education Job Aid 8178604 ML-1 Front-loading Automatic Washer88 pg
    Covers this model
  • TECHNICAL EDUCATION JOB AID 8178686 ML-8 FRONT-LOADING WASHER EPIC z™96 pg
    Covers this model

Tech Tip

  • Instruction Sheet - W10156252 - Rev A - Special Handling2 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MHWE500VW10.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (64)

CodeMeaning
F/02Long drainF/05Water temperature sensor (NTC) value is out of range during the water heating…F/06Drive motor tachometer errorF/07Motor Control Unit (MCU) errorF/09Overflow conditionF/10Motor Control Unit (MCU) heat sink thermal tripF/11Serial communication errorF/13Dispenser circuit errorF/14EEPROM errorF/15Motor Control Unit (MCU) errorF/21CCU / Touchpad / LED assembly errorF/22CCU / Touchpad / LED assembly errorF/dLDoor lock errorF/dUDoor unlock errorF/HNo water detected entering machine or pressure switch trip not detected after…F01EEPROM communication error between the Central Control Unit (CCU) and the…F02Pump drive errorF03Main relays errorF04Heater short circuit to groundF05Steamer defectF06Motor Control Unit (MCU) errorF08No water detected entering machine or pressure switch trip not detectedF09No water detected entering machine or pressure switch trip not detectedF11Motor Control Unit has internal failure; repeating under or over voltage, or…F2Motor Control Unit (MCU) has an internal failure; if failure occurs during…F20No water detected entering machine or pressure switch trip not detectedF21Long drainF22Door lock errorF23Heater failureF24Water temperature sensor error
View all 64 error codes
F25Drive motor tachometer errorF26Door lock errorF27Water heater errorF28Water temperature sensor (NTC) errorF29Door unlock errorF30Motor drive errorF31Door switch errorF32Load detected in drum at start of CLEAN WASHER cycle (detection by weight).F33Dispenser system errorF34Door unlock errorF35Overflow conditionF36Steamer electronic board relays errorF37Total steamer failureF38Steamer inlet valve failureF39Steamer time out reachedF40Drain pump connection lost during the drain cycleF41User Interface heartbeat failureF42Serial communication errorF43Steamer valve failureF44Steamer time out reachedF45Central Control Unit heartbeat failureF46User Interface heartbeat failureF47Not supportedF48Steamer inlet valve failureF49Steamer time out reachedF5Pump driver fails to activate, one of the main relays is not working properly…F50Central Control Unit heartbeat failureF51User Interface heartbeat failureF52MCU heatsink overtemperature errorF53Not supportedF8No water detected entering machine or pressure switch trip not detected…rLUnload indicationSdSuds lockSudSuds lock condition detected

Service modes (13)

  • diagnostic1
  • Diagnostic Test["Washer must be empty and control must be in the OFF state.","Close the door.","Push CONTROL/ON…
  • Diagnostic Test (Full - with error history and software versions)Press and hold a button for 2-5 seconds, then release
  • Diagnostic Test (with error history)["Close the door.","Press and hold any one button for 2-5 seconds, then release.","Press and hold…
  • Diagnostic Test Only (automated test without error history)1
  • diagnostic_test_only1
  • Manual Diagnostic Test["Ensure washer is empty and control is in the OFF state.","Close the door.","Select any one key…
  • Quick Diagnostic Test (Bypass Service History)["Ensure drum is empty.","Close the door.","Push POWER.","Select the CLEAN WASHER cycle.","Press…
  • Quick Diagnostic Test (bypasses error history)1
  • Quick Entry Diagnostic Test (bypassing Service History)1
  • Service History Mode & Diagnostic Test["Ensure washer is empty and control is in the OFF state.","Close the door.","Select any one key…
  • Steamer Functionality CheckupClose the door
  • steamer_functionality_checkup1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass