Model reference

Samsung WF410ANWXAC

Name: Samsung WF410ANWXAC
Brand: Samsung

Washer

1 document31 error codes15 service modes

Available documentation

Service Manual

Error Code Washer16 pg
Covers this model

MyPros+ Max

Diagnose your Samsung WF410ANWXAC.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Samsung Washer

1E on my Samsung WF410ANWXAC

M+

Water level frequency is continuously

From Service Manual 473114, p.46:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part DA92-00384N

Main PCB assembly

Error codes (31)

CodeMeaning

1EWater level frequency is continuously over 30kHz or below 15kHz for 10 seconds…3EMotor overloaded due to too much laundry or motor coil open/cut.3E1Defective Hall Sensor or hall sensor terminal not connected.3E2Motor wire connection fault on Main PBA or Main PBA fault.4EWater level does not increase more than 100Hz from previous water level every 3…5EUnit does not reach target water level after 15 minutes of draining, indicating…8EThe signal of tub location is out of normal range in Mems sensor during…8E1The signal of tub location is out of normal range in Mems sensor during…8E2Rear Mems fault AECommunication error between Main PBA and Sub PBA for over 24 seconds.AE6Communication error between Main PBA and Sub PBA for over 24 seconds (front…bE1A button on the control panel is continually pressed for over 30 seconds.bE2A button on the control panel is continually pressed for over 30 seconds.C/UEWasher detects unbalance 3 times during operation.dEDoor-Lock switch does not detect that the door is closed (Reed S/W for top…dE1Door lock/unlock has failed continuously seven times.dSDoor-Lock switch does not detect that the door is closed.fLDoor lock/unlock has failed continuously seven times.HEHeater fault detected.HE1Heater fault or temperature sensor fault at center of dryer.LEWater level frequency above 30kHz detected for 5 seconds during wash/rinse…LE1Water level frequency above 30kHz detected for 5 seconds during wash/rinse…LODoor lock/unlock has failed continuously seven times.nFWater level does not increase more than 100Hz from previous water level every 3…OEWater level frequency below 21kHz detected for 10 seconds, possibly caused by…PEClutch motor position detection signal not received within 15 seconds after…PE1Hall sensor location detection fails 15 times after running the clutch motor…sudToo much foaming detected during operation.tEWasher detects water temperature is lower than -3 degrees C during heater on…tE1Washer detects water temperature is lower than -3 degrees C during heater on…

View all 31 error codes

tUHSensor bar is short in tSt or SPn test mode.

Service modes (15)

Diagnostic Mode - A-Type (WA45H7*** / WA48H7*** / WA56H9***)From Service Mode, press the Spin key to start Diagnostic Code Check Mode (Code 'd' flashing)
Diagnostic Mode - B-Type (WA50F9*****)From Service Mode, press the Spin key to start Diagnostic Code Check Mode (Code 'd' flashing)
Diagnostic Mode - C-Type (WA400*** / WA422***)From Service Mode, press the Spin key to start Diagnostic Code Check Mode (Code 'd' flashing)
Diagnostic Mode - D-Type (WA456***)From Service Mode, press the Spin key to start Diagnostic Code Check Mode (Code 'd' flashing)
Diagnostic Mode - E-Type (WF42H5*** / WF45H6*** / WF56H9***)From Service Mode, press the Spin key to start Diagnostic Code Check Mode (Code 'd' flashing)
Diagnostic Mode - F-Type (WF393*** / WF405*** / WF433*** / WF455***)From Service Mode, press the Spin key to start Diagnostic Code Check Mode (Code 'd' flashing)
Diagnostic Mode - G-Type (WF457***)From Service Mode, press the 3 key on the bottom to start Diagnostic Code Check Mode (Code 'd'…
Service Mode - A-Type (WA45H7*** / WA48H7*** / WA56H9***)During power on status or normal operation, press Delay End + Pre Soak at the same time for 3…
Service Mode - B-Type (WA50F9*****)During power on status or normal operation, press Delay Start + Pre Soak at the same time for 3…
Service Mode - C-Type (WA400*** / WA422***)During power on status or normal operation, press Delay Start + Extra Rinse at the same time for 3…
Service Mode - D-Type (WA456***)During power on status or normal operation, press Delay Start + Aqua Jet at the same time for 3…
Service Mode - E-Type (WF42H5*** / WF45H6*** / WF56H9***)During power on status or normal operation, press Soil Level + Delay End at the same time for 3…
Service Mode - F-Type (WF393*** / WF405*** / WF433*** / WF455***)During power on status or normal operation, press Signal + Extra Rinse at the same time for 3…
Service Mode - G-Type (WF457***)During power on status or normal operation, tap Segment '4' three times, tap Segment '1' two times…
Water Level Check ModeWith no power, press Spin + Soil Level + Power at the same time, then turn knob dial 3 turns in CCW…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Samsung washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass