mypros+
Model reference

Bosch 58300000158541

Dishwasher

3 documents63 error codes12 service modes

Available documentation

Service Manual

  • Dw Repair Instruction44 pg
    Covers this model
  • Failure storage and Customer Service programs2 pg
    Covers this model
  • Repair manual - Dishwasher109 pg
    Covers this model
MyPros+ Max

Diagnose your Bosch 58300000158541.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (63)

CodeMeaning
E:0000No errorE:01Faulty pump relay or low voltage/excessive voltage drop causing pump failure.E:0100Internal fault power moduleE:0103Power module defect (internal pump control)E:0105Ground fault at Zeolite heater or relay for Zeolite heater defectiveE:0106Ground fault at water heaterE:0107Temperature monitoringE:0108D-Bus power limit exceededE:02Faulty heater relayE:04Faulty safety heater relay or faulty heaterE:05Faulty water switch relayE:06Door ajar, not properly latched, or door latch Hall sensor not detected.E:08Heat pump detects low water levelE:09Faulty/open-circuited heater circuitE:11Heat pump NTC resistances out of range or NTC's show different values.E:13Incoming water too hot (>75°C / 167°F).E:15Water in base activated float switchE:17Inlet water flow rate too highE:18Inlet water flow rate too low or faulty water inlet valveE:20Faulty heat pump motor winding or disconnected heat pump harness.E:2012Heating circuit interrupted (resistance, supply wires, contacts of the safety…E:2030Heating element is calcifiedE:2040Wire or plug interruptedE:2050Safety relay heater defectiveE:2060NTC resistance values are outside permitted rangeE:21Heat pump is blocked or clogged.E:2120Zeolite heater heating circuit interrupted (resistance/supply wires)E:2130Heating faultE:22Water remaining in sumpE:23Faulty drain pump motor winding or disconnected drain pump harness.
View all 63 error codes
E:24Drain obstructionE:25Missing or loose drain pump cover, or drain pump blockedE:26Faulty water switch, water switch motor, or water switch harness.E:27Low supply voltage continuously <85 VACE:28Aqua sensor not properly calibratedE:29Low supply voltage (<85 VAC)E:30High supply voltage (>140 VAC)E:3000Filling faultE:3100Filling faultE:32Overloaded drain pump due to kinked or clogged drain hose (may not show during…E:3200No water supply at start of program or water supply flow is too lowE:3300Water supply flow is too highE:3400Water supply (impulses from flow sensor) without activation of the filling…E:6001Circulation pump faultE:6002Drain pump faultE:6101Open circuit to drain pump or resistance values of drain pump are wrongE:6102Drain pump is blocked or drain pump cover in sump is missing/looseE:6103Non-return valve letting water by or draining is not possible, drain pump cover…E:6900Dispenser or heat exchanger valve faultE:6A00Water switch faultE:8000Door Hall sensor faultE:8101Aquasensor faultE:9000Under/over voltage errorE:9001Undervoltage faultE:9010Over voltage error (>142V)E:9240Zeolite fan defective or blocked, open circuit to Zeolite fan, or resistance…E0No errors detected.E1Heating error.E2NTC (temperature sensor) error.E3Filling errorE4Water switch cannot be positioned.E5Safety float water level reached or motor speed error (model dependentE6Aqua sensor error.

Service modes (12)

  • Customer Service Program (P1)["Enter the Special Functions Menu first.","While in the Special Functions Menu, press the 'B4' key…
  • Customer service test program (P1)["While pushing and holding any two wash cycle buttons, turn the dishwasher on with the on/off…
  • Customer settings (codings) mode1
  • Dishwasher resetPress and hold Start/Reset for at least 3 seconds to reset dishwasher.
  • End of cycle tone volume change["Turn the dishwasher off.","Push and hold the right Cancel/Reset button while turning the…
  • Extra dry heat setting change["Turn the dishwasher off.","Push and hold the left Cancel/Reset button while turning the…
  • Failure Storage["Enter the Special Functions Menu first.","Press 'B4' until the following is displayed
  • Power module reset - Method 11
  • Power module reset - Method 21
  • Sales demo (showroom) program (C9)["Enter the special program mode by holding any two wash cycle buttons while turning on the…
  • Special Functions Menu["Power off dishwasher by pressing 'On/Off' button.","Press and hold 'B4' + 'Start'…
  • Special programs and coding menu["While pushing and holding any two wash cycle buttons, turn the dishwasher on with the on/off…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Bosch dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax