mypros+
Model reference

Fisher & Paykel GWL03US

Washer

7 documents54 error codes16 service modes

Available documentation

Service Manual

  • Smart Drive Electronic Washing Machine Model GWL03US75 pg
    Covers this model
  • Smart Drive Electronic Washing Machine75 pg
    Covers this model
  • ELECTRONIC WASHING MACHINE MODEL GWL10US Service Supplement32 pg
    Covers this model
  • ELECTRONIC WASHING MACHINE MODEL GWL10US Service Supplement31 pg
    Covers this model
  • ELECTRONIC WASHING MACHINE MODEL GWL10US Service Supplement29 pg
    Covers this model
  • Smart Drive Electronic Washing Machine Model GWL08US20 pg
    Covers this model
  • SMART DRIVE ELECTRONIC WASHING MACHINE MODEL GWL08US Service Supplement20 pg
    Covers this model
MyPros+ Max

Diagnose your Fisher & Paykel GWL03US.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (54)

CodeMeaning
1Motor Controller Module memory error.10Temperature sensor may be open circuit or ambient temperature is below -10°C.104Display to Motor Controller Module communications error (see fault code 106).105Display to Motor Controller Module communications error (see fault code 106).106Display to Motor Controller Module communications errors detected by the…107Motor Control Module reset error11Pressure sensor detected a negative pressure while measuring water level.12Flood protection error130Single Rotor Position Sensor error131Repetitive Rotor Position Sensor error132Single current trip133Repetitive current trip134Single current trip and Rotor Position Sensor error detected simultaneously.136Motor stall160Basket engaged161Hardware/EEPROM supply mismatch162Brake deceleration time-out163Valve reset pin connect fault164Brake function time-out192Motor PMW reset pin connect fault2Error encountered when trying to read the pressure sensor.3Motor Controller Module memory error.36Water leak fault37Pump blocked error38Pressure sensor recorded water level of empty while agitating; pressure sensor…39Pressure tube fault40Basket dis-engage fault41Temperature sensor measuring temperatures above 230°F (110°C), probably due to…43Out of balance switch indicates permanently on or harness disconnected.44Water sensed in basket during spin; slow pump out rate due to pump hose or pump…
View all 54 error codes
45Display memory check fault47Basket dis-engage fault48Both hot and cold water valves faulty49Cold water valve faulty50Hot water valve faulty51Diverter valve timeout fault52Diverter valve top-up fault53Rotor Position Sensor step fail54Motor/Motor Controller Module step fail56Basket check no valid fault57Brown out during Display EEPROM write58Pressure transducer at maximum adjustment fault59ID out of range fault6Motor Controller Module received an incorrect signal from the pressure sensor.60Motor Controller memory check fault61Brown out during Motor Controller EEPROM write62Pump over-current fault63Pump communications fault64Pressure transducer frequency out of range (<66kHz).65Pressure transducer frequency out of range (>80kHz).66Pressure transducer frequency out of range (>90kHz).7Display Module has found a memory fault.81-95Display to Motor Controller Module communications errors (see fault code 106).9Display size switch setting does not match that stored in the memory.

Service modes (16)

  • Data Display (Fault Code Read)["Enter Diagnostic Mode.","Press the SPIN SPEED UP button until the HOLD and SLOW SPIN LEDs are on…
  • Data Display Mode1
  • Demonstration ModePress and hold down the ADVANCE button, then press the POWER button.
  • Diagnostic Mode["Turn the power on at the power point and off at the console.","Press and hold the WASH…
  • Drain Pump Test["Enter Diagnostic Mode.","Press the REGULAR CYCLE button to turn the drain pump on or off.","The…
  • Fault Code Display (Data Display)["Enter Diagnostic Mode.","Press SPIN SPEED UP button until HOLD and SLOW SPIN LEDs are on (binary…
  • Hot Tub Flag Clear["Enter Diagnostic Mode.","If WATER SAVER LED is on, spin speed is restricted to 700 RPM.","Press…
  • Lid Switch & Out of Balance Switch Test["Enter Diagnostic Mode.","Press SPIN SPEED UP button until the MEDIUM SPIN LED is on (binary count…
  • Machine Size Setting Mode["Turn the power on at the power point and off at the console.","Press and hold the WASH TEMP UP…
  • Option Adjustment ModePress and hold down the START/PAUSE button, then press the POWER button
  • Re-Cycle Feature Toggle["Enter Diagnostic Mode.","Press WATER LEVEL UP button to toggle RE-CYCLE on/off.","MEDIUM WATER…
  • Re-Start Feature Toggle["Enter Diagnostic Mode.","Press WATER LEVEL DOWN button to toggle RE-START on/off.","LOW WATER…
  • Recirculating Valve Test["Enter Diagnostic Mode.","Press the Delicate button to turn the recirculating valve on and off."]
  • Size Setting Mode["Turn the power on at the power point and off at the console.","Press and hold the TEMPERATURE UP…
  • Switch Test ModeIn Diagnostic Mode, press the ADVANCE button to turn the HIGH WATER LEVEL LED off.
  • Water Valve Test["Enter Diagnostic Mode.","Press WASH TEMPERATURE DOWN button to turn Cold Water Valve on (Cold…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Fisher & Paykel washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass