Model reference

Fisher & Paykel GWL11-96151B

Name: Fisher & Paykel GWL11-96151B
Brand: Fisher & Paykel

Washer

5 documents94 error codes8 service modes

Available documentation

Service Manual

ELECTRONIC WASHING MACHINE PHASE 6 Series 11 120v 60 Hz41 pg
Covers this model
ELECTRONIC WASHING MACHINE PHASE 6 Series 11 120v 60 Hz41 pg
Covers this model
Smart Drive Electronic Washing Machine25 pg
Covers this model
Smart Drive® Electronic Washing Machine19 pg
Covers this model
Smart Drive® Electronic Washing Machine19 pg
Covers this model

MyPros+ Max

Diagnose your Fisher & Paykel GWL11-96151B.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Fisher & Paykel Washer

1 on my Fisher & Paykel GWL11-96151B

M+

Motor Controller Module (Display Module

From Service Manual 524074, p.46:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure drive motor winding resistance. Expected: 2 to 6 ohms between winding pairs.

3.Rotate the drum by hand. Inspect the belt and pulley for glaze or wear.

Part W10006384

Drive motor

Error codes (94)

CodeMeaning

1Motor Controller Module (Display Module for Phase 1) has encountered an error…10Temperature Sensor (Thermistor) Error 104Phase 2 to 6 communication error (see fault code 106).105Phase 2 to 6 Comms Error Time out 106Phase 2 to 3 (and Phase 6 IW) Display to Motor Controller Communications Error.107Phase 2 to 6 Motor Controller Module Reset Error 108Phase 6 IW Comms CRC Error (see fault code 106).11Pressure Sensor Fault 12Flood Protection Error 127Phase 5 Machine Set up Error 13Phase 1 Pump Fault 130Single Rotor Position Sensor Error 131Repetitive Rotor Position Sensor Error 132Phase 1 to 4 Single Current Trip 133Phase 1 to 4 Repetitive Current Trip 134Phase 4 Single Current Trip & Rotor Position Error 136Motor Stall 14Phase 1 Pump Connection Fault 144Phase 1 Motor Controller Software Trap 15Phase 1 Display Module Fault 160Basket Engaged 161Phase 2 to 6 Hardware/EEPROM Supply Mismatch 162Phase 3 to 5 Brake Deceleration Time-out Fault 163Phase 4 to 6 Valve Reset Pin Connect Fault 164Phase 4 to 5 Brake Function Time-out Fault 17Phase 1 Display / Motor Controller out of Sequence.18Phase 1 Display / Motor Controller out of Sequence.19Phase 1 Display / Motor Controller out of Sequence.192Phase 4 to 5 Motor PWM Reset Pin Connect Fault 2An error has been encountered when trying to read the pressure sensor.

View all 94 error codes

20Phase 1 Display / Motor Controller out of Sequence.22Phase 1 Display / Motor Controller out of Sequence.23Phase 1 Display / Motor Controller out of Sequence.230Phase 6 EEPROM Value out of Range 231Phase 6 MW GW Link Error 232Phase 6 COMMS Timeout 5 Sec 233Phase 6 EEPROM Read Error 234Phase 6 Lid Lock Open Circuit 235Phase 6 Lid Lock Short Circuit 236Phase 6 Incompatible EEPROM Version 237Phase 6 Temperature Sensor Error 238Phase 6 Lid Lock Fail In-Line Test (1)239Phase 6 Lid Lock Fail In-Line Test (2)240Phase 6 Hall Out Of Order / RPS Fault 241Phase 6 Function Time Out 242Phase 6 OOB Hit Greater than Max for 5 Sec 243Phase 6 Stepper Test Failure 25Phase 5 IW LCD Initialisation Error 28Phase 1 Display / Motor Controller out of Sequence.29Phase 1 Display / Motor Controller out of Sequence.3The Motor Controller Module has found a memory error.30Phase 1 Display / Motor Controller out of Sequence.32Phase 1 Pump Circuit Error 33Phase 1 Water Valve Fault 34Phase 1 Brake Resistor Fault 35Phase 1 MC Reset Error 36Water Leak Fault 37Pump Blocked Error 38Pressure Sensor Fault 39Pressure Tube Fault 4Phase 1 Communications Fault 40Bowl Dis-engage Fault 41Temperature Sensor Fault (Thermistor)42Phase 1 Rotor Fault 43OOB Switch Fault 44Water in Tub during Spin 45Phase 5 Display Memory Check Fault 46Phase 5 IW Display EEPROM Check 47Phase 2 and 3 Basket Dis-engage Fault 48Hot and Cold Valve Faulty 49Cold Valve Faulty (proportional)5Phase 1 Communications Fault 50Hot Valve Faulty (digital)51Phase 5 and 6 Eco Diverter Valve Fault 52Phase 5 and 6 Eco Diverter Top-up Fault 53Rotor Position Sensor Step Fail 54Motor/Motor Controller Module Step Fail 55Phase 3 to 6 System Step Fail 56Phase 4 to 6 Basket Check No Valid Fault 57Phase 4 to 6 Brown Out During Display EEPROM Write Fault 58Phase 4 to 5 Pressure Transducer at Maximum Adjustment 59Phase 4 to 5 ID Out of Range Fault 6The Motor Controller module (Display Module for Phase 1) has received an…60Phase 4 to 6 Motor Control Memory Check Fault 61Phase 4 Brown Out During Motor Controller EEPROM Write Fault 62Phase 5 Pump Over Current 63Phase 5 Pump Comms Error 64Phase 5 and 6 Pressure Transducer (Ptx) error 65Phase 5 and 6 Pressure Transducer (Ptx) error 66Pressure Transducer Error 7The Display module has found a memory fault.8Phase 1 Display Module Fault 81Phase 2 to 3 Display/Motor Controller communication error (see fault code 106).9Size Switch Error

Service modes (8)

demonstrationPress and hold the ADVANCE button, then press the POWER button.
Demonstration Mode1
diagnostic1
Diagnostic Mode1
Pump Pulse Setting (within Size Setting Mode)1
Restart/Recycle Setting Mode1. Enter Diagnostic Mode (power on at wall, off at console; press and hold WASH TEMPERATURE DOWN…
Size Setting Mode1
size_setting1. Turn power on at the power point and off at the console. 2. Press and hold the TEMPERATURE UP…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Fisher & Paykel washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass