mypros+
Error code reference

Fisher & Paykel Washer Error Code 233

Phase 6 EEPROM Read Error

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 233 error code actually means

Your Fisher & Paykel washer is having trouble reading important stored information from the part that controls the motor. This prevents the washer from running its cycle properly. A technician will most likely need to replace the motor control board to fix this issue.

Diagnostic procedure

The full 233 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Replace Motor controller.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 233 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 233

Ranked by how often they cause this code
  1. 1Failed Motor Controller Board
  2. 2Corrupted EEPROM Data
  3. 3Loose or Damaged Wiring Connector
  4. 4Damaged Wiring Harness
  5. 5Main Control Board Fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 233

What does 233 mean on a Fisher & Paykel washer?
Error code 233 on a Fisher & Paykel washer is a Phase 6 EEPROM Read Error. It means the washer's control system is unable to read stored data from the motor controller's EEPROM memory during a specific phase of operation. This prevents the machine from completing its cycle, and the motor controller is the primary component to inspect and replace.
Will resetting my Fisher & Paykel washer clear error code 233?
A power reset may temporarily clear the error code display, but it will not resolve the underlying hardware fault causing the EEPROM read failure. If the motor controller or its memory is genuinely faulty, the error will return as soon as the washer attempts to run through the affected phase again. A proper repair, not just a reset, is needed to permanently resolve this fault.
How much does it cost to repair error code 233 on a Fisher & Paykel washer?
Repair costs will vary depending on whether the fix involves reseating connectors or replacing the motor controller board. A wiring or connector fix carried out by a technician may cost in the range of $75 to $150 for labor. If the motor controller board requires replacement, the total cost including parts and labor typically falls in the range of $200 to $450, depending on parts availability and local labor rates.
Can I fix error code 233 on my Fisher & Paykel washer myself?
A knowledgeable DIYer can start by inspecting the wiring harness and connectors between the motor controller and main control board for any loose, corroded, or damaged connections and reseating them. However, if the fault lies within the motor controller board itself, replacing that component requires identifying the correct replacement part and safely working with the washer's electrical system. If you are not comfortable working with appliance electronics, a qualified technician is recommended.
Is it safe to use my Fisher & Paykel washer when error code 233 is showing?
It is not advisable to continue using the washer while this error is active. The fault indicates the control system cannot read critical operational data from the motor controller, which means the washer may not be able to manage the motor correctly during the cycle. Continuing to run the machine under these conditions could potentially cause further damage to the motor or other components.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass