mypros+
Model reference

GE GFWH1200D1WW

Washer

6 documents62 error codes19 service modes

Available documentation

Tech Sheet

  • GE Washer Tech Sheet8 pg
    Covers this model
  • Tech sheet8 pg
    Covers this model

Service Manual

  • GE Appliances Front Load Washer Technical Service Guide70 pg
    Covers this model
  • Service Technician Only - Diagnostic Guide8 pg
    Covers this model

Service Flash

  • TB03 12 GE HA Washer Training Bulletin7 pg
    Covers this model

Tech Tip

  • Loose Drain Pump Access Door2 pg
    Covers this model
MyPros+ Max

Diagnose your GE GFWH1200D1WW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (62)

CodeMeaning
22Fill problems23Fill problems31Drain problems38Dispenser problems39Dispenser problems42Motor drive operation above design limits.43Motor drive internal problems.44Motor drive operation above design limits.46Motor drive operation above design limits.47Motor drive operation above design limits.48Motor drive operation above design limits.49Motor drive operation above design limits.4AMotor drive internal problems.4BMotor drive internal problems.4CMotor drive internal problems.50Motor drive internal problems.52Motor drive internal problems.53Motor drive internal problems.54Motor drive internal problems.55Main control internal problems.56Main control internal problems.57Main control internal problems.58Main control internal problems.60Door lock assembly problems61Door lock assembly problems62System contact failure63Door lock assembly problems64Door lock assembly problems65Water level sensor problems.66Water temperature sensor (thermistor) problems.
View all 62 error codes
67Water temperature sensor (thermistor) problems.71Main control internal problems.80Water level sensor problems.81Water level sensor problems.82Water level sensor problems.E22Fill problem detected by the control.E23Fill problem detected by the control.E31Drain problem detected by the control.E38Dispenser mechanism problem detected.E39Dispenser mechanism problem detected.E42Motor drive operation above design limits.E45Motor drive operation above design limits.E46Motor drive operation above design limits.E47Motor drive operation above design limits.E48Motor drive operation above design limits.E4AMotor drive internal problem.E4BMotor drive internal problem.E4CMotor drive internal problem.E50Motor drive internal problem.E52Motor drive internal problem.E54Motor drive internal problem.E56Main control internal problem.E57Main control internal problem.E58Main control internal problem.E60Door lock assembly problem.E61Door lock assembly problem.E62System contact failure.E63Water level sensor problem.E64Water level sensor problem.E65Water level sensor problem.E66Water temperature sensor (thermistor) problem.E67Water temperature sensor (thermistor) problem.

Service modes (19)

  • Control Board Programming (t01)1
  • Control Board Programming Mode (t01)Replacement control board automatically enters t01 on initial power-up
  • control_board_programming1
  • diagnosticWithin 30 seconds of plugging in the washer, press Temp, then Wash (Signal on some models), then…
  • Service Test Mode1. Machine must be in idle mode (all LEDs on display off). 2. Press the following key sequence…
  • Service/Diagnostic ModeWithin 30 seconds of plugging in the washer, press Temp, eWash, Temp, eWash.
  • t01 - Model IDFrom service test mode, press Start/Pause
  • t02 - Fault CodesFrom service test mode, navigate to t02 and press Start/Pause
  • t03 - Software IDFrom service test mode, navigate to t03 and press Start/Pause to alternate between UL (UL code)…
  • t04 - LED Illumination and Button TestFrom service test mode, navigate to t04 and press Start/Pause.
  • t05 - Pump TestFrom service test mode, navigate to t05 and press Start/Pause.
  • t06 - Water Level Sensor TestFrom service test mode, navigate to t06 and press Start/Pause
  • t07 - Thermistor/Heater TestFrom service test mode, navigate to t07 and press Start/Pause.
  • t08 - Steam TestFrom service test mode, navigate to t08 and press Start/Pause.
  • t09 - Spray TestFrom service test mode, navigate to t09 and press Start/Pause.
  • t10 - Tumble TestFrom service test mode, navigate to t10 and press Start/Pause.
  • t11 - Spin TestFrom service test mode, navigate to t11 and press Start/Pause
  • t12 - Dispenser TestFrom service test mode, navigate to t12 and press Start/Pause to advance
  • t13 - EOL TestFrom service test mode, navigate to t13 and press Start/Pause.

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass