Model reference

GE GFWH1200DWW

Name: GE GFWH1200DWW
Brand: GE

Washer

11 documents112 error codes22 service modes

Available documentation

Tech Sheet

GE Washer Tech Sheet8 pg
Covers this model
Tech sheet8 pg
Covers this model

Service Manual

GE Appliances Front Load Washer Technical Service Guide70 pg
Covers this model
Service Technician Only - Diagnostic Guide8 pg
Covers this model
Technical Service Guide - UltraFresh Front Load Washer82 pg
Covers this model
UltraFresh Front Load Washer Service Guide100 pg
Covers this model

Bulletin

Loose Drain Pump Door2 pg
Covers this model

Service Flash

Frontload Washer Makes a High Pitch Noise during Spin1 pg
Covers this model
TB03 12 GE HA Washer Training Bulletin7 pg
Covers this model

Tech Tip

Loose Drain Pump Access Door2 pg
Covers this model

Other

HL03 12 GE Washer FL Stuck Door Lock PLunger1 pg
Covers this model

MyPros+ Max

Diagnose your GE GFWH1200DWW.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (112)

View all 112 error codes

43Inverter Fault 44Inverter Fault 45Inverter Fault 46Inverter Fault 47Inverter Fault 48Inverter Fault 49Inverter Fault 4AMotor drive internal problems.4BMotor drive internal problems.4CMotor drive internal problems.50Inverter Fault 51Inverter Fault 52Motor drive internal problems.53Motor drive internal problems.54Motor drive internal problems.55Main control internal problems.56Main control internal problems.57Door Lock Fault Water Above Door by Pressure 58ADC Health Check Fault 59Accelerometer Fault 6Critical Flood Level by Pressure 60Accelerometer Fault 61Accelerometer Fault 62Inverter Power And Door Lock Monitor 63Accelerometer Fault 64Accelerometer Fault 65Pressure Sensor Continuous Gallons Monitor 66Inverter Fault 67Inverter Fault 68Inverter Fault 69Inverter Fault 70Inverter Volt/Hertz Start Up 71Inverter Fault 72Inverter Fault 73Inverter Fault 74Inverter Fault 77Critical Door Lock Failure: Can't Unlock Door 78Board Communication API Mismatch 8Pressure Sensor Loss 80Water level sensor problems.81Water level sensor problems.82Water level sensor problems.83Inverter Fault 84Vent Damper Fault 85Voltage Detected by MC is outside acceptable window.87Accelerometer Fault 88Accelerometer Fault 89Accelerometer Fault 9Door Switch Redundancy 90Accelerometer Fault 91UI - Main Board Heartbeat Timeout 92Inverter Fault 93Main Board Component Failure 94Water Quality Sensor (Turbidity Sensor) Fault 98Humidity Sensor I2C Communication Failure E22Fill problem detected by the control.E23Fill problem detected by the control.E31Drain problem detected by the control.E38Dispenser mechanism problem detected.E39Dispenser mechanism problem detected.E42Motor drive operation above design limits.E45Motor drive operation above design limits.E46Motor drive operation above design limits.E47Motor drive operation above design limits.E48Motor drive operation above design limits.E4AMotor drive internal problem.E4BMotor drive internal problem.E4CMotor drive internal problem.E50Motor drive internal problem.E52Motor drive internal problem.E54Motor drive internal problem.E56Main control internal problem.E57Main control internal problem.E58Main control internal problem.E60Door lock assembly problem.E61Door lock assembly problem.E62System contact failure.E63Water level sensor problem.E64Water level sensor problem.E65Water level sensor problem.E66Water temperature sensor (thermistor) problem.E67Water temperature sensor (thermistor) problem.

Service modes (22)

Consumer Fault Code ModeFrom an idle state (all LEDs off), press and hold Start pad for 10 seconds
Control Board Programming (t01)1
Control Board Programming Mode (t01)Replacement control board automatically enters t01 on initial power-up
control_board_programming1
diagnosticWithin 30 seconds of plugging in the washer, press Temp, then Wash (Signal on some models), then…
Service ModePress and hold Start pad while rotating the cycle selection knob seven clicks, then release the…
Service Mode (Field Service Mode)Press and hold Start pad while rotating cycle selection knob 180 degrees, then release Start pad.
Service Test Mode1. Machine must be in idle mode (all LEDs on display off). 2. Press the following key sequence…
Service/Diagnostic ModeWithin 30 seconds of plugging in the washer, press Temp, eWash, Temp, eWash.
t01 - Model IDFrom service test mode, press Start/Pause
t02 - Fault CodesFrom service test mode, navigate to t02 and press Start/Pause
t03 - Software IDFrom service test mode, navigate to t03 and press Start/Pause to alternate between UL (UL code)…
t04 - LED Illumination and Button TestFrom service test mode, navigate to t04 and press Start/Pause.
t05 - Pump TestFrom service test mode, navigate to t05 and press Start/Pause.
t06 - Water Level Sensor TestFrom service test mode, navigate to t06 and press Start/Pause
t07 - Thermistor/Heater TestFrom service test mode, navigate to t07 and press Start/Pause.
t08 - Steam TestFrom service test mode, navigate to t08 and press Start/Pause.
t09 - Spray TestFrom service test mode, navigate to t09 and press Start/Pause.
t10 - Tumble TestFrom service test mode, navigate to t10 and press Start/Pause.
t11 - Spin TestFrom service test mode, navigate to t11 and press Start/Pause
t12 - Dispenser TestFrom service test mode, navigate to t12 and press Start/Pause to advance
t13 - EOL TestFrom service test mode, navigate to t13 and press Start/Pause.

Full entry steps, exit procedures, and test sequences are available in Max.

Related GE washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass