mypros+
Model reference

Whirlpool GHW9460PL0

Washer

8 documents50 error codes9 service modes

Available documentation

Tech Sheet

  • Service Technical Sheet16 pg
    Covers this model
  • Tech Sheet - 818227716 pg
    Covers this model
  • Tech Sheet 8182277 GHW9400PL012 pg
    Covers this model
  • Whirlpool Washer Tech Sheet GHW9150PW416 pg
    Covers this model

Service Flash

  • Service Pointer - 8178536 (Leaking in Bulky Cycle)1 pg
    Covers this model
  • Service Pointer - Whirlpool Front Loading Washer Leaking in Bulky Cycle1 pg
    Covers this model

Quick Reference

  • Quick Reference Manual2 pg
    Covers this model

Installation Guide

  • Instruction Sheet2 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool GHW9460PL0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (50)

CodeMeaning
dLDoor lock errordUDoor unlock errorF/01No water entering machine detected within 30 seconds (valves turned off) OR…F/02Drain time exceeds eight minutes; water valves are turned off.F/05Water temperature sensor (NTC) value is out of range during water heating step…F/06Drive motor tachometer error; control is unable to properly detect motor speed…F/07Motor Control Unit (MCU) error; main control has detected a short in the MCU.F/09Overflow condition; overflow contact on pressure switch is closed for more than…F/10MCU heat sink thermal protector has tripped due to overheating, stopping motor…F/11Serial communication error between the Central Control Unit (CCU) and the Motor…F/13Dispenser system error; dispenser motor cannot be driven to its proper position.F/14EEPROM error; error reading data from the EEPROM onboard the CCU.F/15Motor Control Unit (MCU) error; MCU detects multiple resets or errors during a…F/21System leak; no water entry detected within 30 seconds or flow sensor detected…F/22CCU/touchpad-LED assembly communication errorF/COMSerial communication errorF/CWLoad detected in drum at start of Clean Washer cycle (detection by weight).F/dlCCU/touch-pad/LED communication error; touch-pad/LED assembly is not able to…F/DSDoor switch errorF/DSPDispenser system errorF/dUDoor lock error; door cannot be locked after six attempts.F/EPump driver fails to activate, one of the main relays is not working properly…F/HNo water detected entering the machine or no pressure switch trip detected…F/H2ONo water detected entering machine or pressure switch trip not detected…F/HEWater heating errorF/MCUMCU thermal protector tripF/NTCWater temperature sensor (NTC) errorF/OFLOverflow conditionF/PMPPump drive system errorF/SPDMotor speed detection error
View all 50 error codes
F01Pump driver fails to activate, one of the main relays is not working properly…F06Motor Control Unit (MCU) has an internal failureF20No water detected entering machine or pressure switch trip not detectedF21Long drainF22Door lock errorF23Water heater failureF24Water temperature sensor (NTC) errorF25Motor speed detection errorF26Door switch errorF27Overflow conditionF28Serial communication errorF31Door unlock errorF33Dispenser system errorF35MCU over-temperature errorF40Pump drive system errorF42Load detected in drum at start of Clean Washer cycle (detection by weight).FHPressure switch failure; no water entering machine detected within 30 seconds…MCUMotor Control Unit has internal failure; if failure occurs during high-speed…SdSuds lockSudSuds lock condition detected by MCU analyzing current draw on drive motor; may…

Service modes (9)

  • diagnostic["Ensure washer is empty and control is in OFF state.","Close the door.","Push CONTROL/ON (if…
  • Diagnostic Test Mode1
  • Last Stored Failure Code Recall1
  • Manual Diagnostic Test["Washer must be empty and control must be in OFF state.","Close the door.","Select any one key…
  • Quick Diagnostic Test (bypassing Service History)["Drum must be empty.","Close the door.","Push POWER.","Select the CLEAN WASHER cycle.","Press…
  • Quick Entry Diagnostic Test (bypassing Service History Mode)["Ensure drum is empty.","Close the door.","Push POWER.","Select the CLEAN WASHER cycle.","Press…
  • Service History Mode & Diagnostic Test["Washer must be empty and control must be in OFF state.","Close the door.","Select any one key…
  • Washer Monthly Maintenance/Cleaning Cycle (Kenmore Elite HE)1
  • Washer Monthly Maintenance/Cleaning Cycle (Whirlpool Duet)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass