mypros+
Model reference

Bosch SHP65CM

Dishwasher

3 documents83 error codes9 service modes

Available documentation

Service Manual

  • Repair manual - Dishwasher158 pg
    Covers this model
  • Failure storage and Customer Service programs2 pg
    Covers this model

Wiring Diagram

  • Wiring Diagram2 pg
    Covers this model
MyPros+ Max

Diagnose your Bosch SHP65CM.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (83)

CodeMeaning
E:0000No errorE:01Faulty relay to heat pump heater or heat/drain pump disconnected or faultyE:0100General or undetermined power module errorE:0103Failed heater relayE:0105Failed safety relayE:0106Failed water switch triacE:0107PTC temperature sensor failure at power moduleE:0108D-bus (13.5 VDC) power limit exceeded due to excessive currentE:010FSPAU automatic update of power module failedE:0110Failed SystemMaster (SMM) module, power module or harness preventing D-bus…E:02Faulty heat pump heater relay or ground fault at heat pump/zeolite heaterE:03Overheated power module / power cord connection detected by on-board PTC…E:04Faulty safety heater relay on power module or ground fault at heat pump heater…E:05Faulty water switch relay on power moduleE:050FSPAU automatic update of touch pad (IABO) failedE:06Door ajar, not properly latched, popped open, or faulty/misaligned door latch…E:060FSPAU automatic update of 2nd replacement touch pad (IABO) failedE:07Zeolite fan faulty or blocked.E:08Heat pump detects low water levelE:09Faulty heater circuit (open-circuited)E:10Faulty or blocked zeolite fan, or faulty/loose zeolite heater harness.E:100FSPAU automatic update of time light failedE:101FSPAU automatic update of emotion light pro failedE:11Heat pump NTC resistances out of range.E:12Heat pump heater calcifiedE:13Incoming water temperature too high (>75°C / 167°F)E:14Faulty flow meterE:15Water in base activated float switchE:16Flow meter senses water flow with closed inlet valveE:17Inlet water flow rate / pressure too high
View all 83 error codes
E:18Inlet water flow rate / pressure too lowE:185FSPAU automatic update system failedE:19Loose/faulty harness to detergent actuator or faulty dispenser actuator.E:190FSPAU automatic update of controlled lower spray arm (CLS) failedE:192FSPAU automatic update of storage fan failedE:20Faulty heat pump motor winding, pump disconnected, or pump blocked/cloggedE:2012NTC temperature sensor / harness failureE:2030Burnt heat pump heaterE:2040Temperature too high (>78°C / 172°F)E:2050No water in heat pumpE:2060Calcified heat pump heaterE:21Heat pump is blocked / clogged.E:2120Burnt zeolite heaterE:2130Zeolite fan motor failureE:22Water in sumpE:23Faulty drain pump motor winding.E:24Dishwasher won't drainE:25Drain pump blocked or drain pump cover is loose/missingE:26Faulty water switch harness or faulty water switch/motorE:27Continual low supply voltage (<85 VAC)E:28Aqua sensor not properly calibratedE:29Temporary low supply voltage (<85 VAC)E:30Temporary high supply voltage (>140 VAC)E:3000Undetermined flow meter errorE:31Water in zeolite containerE:3100Water leaked into baseE:32Internal error (reserved)E:3200Water inlet flow too lowE:33Controlled lower spray arm rotation blocked.E:3300Water inlet flow too highE:34Controlled lower spray arm reference position not detected.E:3400Water valve stuck open and water doesn't stop fillingE:35Controlled lower spray arm not mounted.E:36Power limit to CLS drive motor exceeded.E:37Failed SystemMaster (SMM) module, power module or harness preventing D-bus…E:6001Heat pump motor winding failureE:6002Heat pump blockedE:6101Drain pump motor winding / harness failureE:6102Drain pump blocked or drain pump cover is loose / missingE:6103Drain system blocked or drain check valve faulty, no draining possibleE:6160Controlled lower spray arm reference position not detectedE:6161Power limit to CLS drive motor exceededE:6900General dispenser or sump back flow / check valve errorE:6A00Water switch reference gear not detectedE:8000Door ajar, faulty door latch or faulty door Hall sensorE:8101Aqua sensor not calibratedE:9000Temporary low supply voltageE:9001Continual low supply voltageE:9010Temporary high supply voltageE:9100Temperature too high (>75°C / 167°F)E:9210Controlled lower spray arm rotation blockedE:9211Controlled lower spray arm not mountedE:9240Filter blocked, no draining possible

Service modes (9)

  • Auto Door Open Quick Check Test["Turn the dishwasher off.","While pressing and holding the 2nd & 3rd cycle buttons left of the…
  • CS Test Program / Component Test Mode["Reset and turn off the dishwasher.","While pressing and holding the 'Speed 60' and 'Start'…
  • Customer Service Program (P1)["Enter the Special Functions Menu first.","While in the Special Functions Menu, press the 'B4' key…
  • Customer Settings / Coding Mode["Turn off dishwasher and ensure no wash programs are running.","Open the door (top button…
  • Failure Storage["Enter the Special Functions Menu first.","Press 'B4' until the following is displayed
  • Power Module Reset (Method 1)["With door closed and dishwasher turned on, press and hold Start for 5 seconds.","Display should…
  • Power Module Reset (Method 2)["Disconnect power supply to dishwasher.","Remove toe panel.","Disconnect drain pump harness from…
  • Service Mode (iService/App Error Log Access)["Press and hold the Remote Start or Home Connect button.","While holding that button, press and…
  • Special Functions Menu["Power off dishwasher by pressing 'On/Off' button.","Press and hold 'B4' + 'Start'…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Bosch dishwasher models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass