mypros+
Model reference

Fisher & Paykel GWL03-96986

Washer

3 documents54 error codes13 service modes

Available documentation

Service Manual

  • ELECTRONIC WASHING MACHINE MODEL GWL10US Service Supplement32 pg
    Covers this model
  • ELECTRONIC WASHING MACHINE MODEL GWL10US Service Supplement31 pg
    Covers this model
  • ELECTRONIC WASHING MACHINE MODEL GWL10US Service Supplement29 pg
    Covers this model
MyPros+ Max

Diagnose your Fisher & Paykel GWL03-96986.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (54)

CodeMeaning
1Motor Controller Module memory error.10Temperature sensor may be open circuit or ambient temperature is below -10°C.104Display to Motor Controller Module communications error (see fault code 106).105Display to Motor Controller Module communications error (see fault code 106).106Display to Motor Controller Module communications errors; Display Module…107Motor Controller Module reset error; Display Module detected Motor Controller…11Pressure sensor detected a negative pressure while measuring water level.12Water level found above flood level; unable to lower below flood level after…130Single Rotor Position Sensor error; Motor Controller found an error in the…131Repetitive Rotor Position Sensor error; continuous condition similar to fault…132Single current trip; Motor Controller Module detected excess current in the…133Repetitive current trip; Motor Controller detected excess current in motor or…134Single current trip and Rotor Position Sensor error detected simultaneously.136Motor stall; Motor Controller Module unable to start the motor due to faulty…160Basket re-engaged during agitate; possible leak in air bell, basket overloaded…161Hardware/EEPROM supply mismatch; Motor Controller checks hardware configuration…162Brake deceleration time-out fault; basket has not come to a stop in permitted…163Valve reset pin connect fault; Motor Controller sensed PCB connection is open…164Brake function time-out fault; Motor Controller has been attempting to brake…192Motor PWM reset pin connect fault.2Error encountered when trying to read the pressure sensor.3Motor Controller Module memory error.36Water leak fault; Motor Controller Module needed to top up water level more…37Pump blocked error; water level reading from pressure sensor has not changed…38Pressure sensor recorded empty water level while agitating; pressure sensor…39Pressure tube may be blocked, kinked, or fallen off completely; alternatively…40Basket dis-engage fault; basket not engaged even though pressure sensor…41Temperature sensor measuring temperatures above 230°F (110°C), probably due to…43Out of balance switch signal indicates switch is permanently on or harness to…44Water sensed in basket during spin; slow pump out rate due to pump hose or pump…
View all 54 error codes
45Display memory check fault; on power up the display checked its memory against…47Basket dis-engage fault; unable to determine valid basket status after 2-minute…48Both hot and cold water valves faulty; valve diagnostic circuit indicates both…49Cold water valve faulty; valve diagnostic circuit indicates cold valve is…50Hot water valve faulty; valve diagnostic circuit indicates hot valve is faulty…51Diverter valve timeout fault; machine detected diverter valve is leaking water…52Diverter valve top-up fault; machine exceeded maximum number of top-ups during…53Rotor Position Sensor step fail; motor step test found motor did not step in…54Motor/Motor Controller Module step fail; motor step test found motor did not…56Basket check no valid fault; machine unable to determine a valid basket status…57Brown out during Display EEPROM write; 15-volt supply found below safety level…58Pressure transducer at maximum adjustment fault; Display Module checked memory…59ID out of range fault; Display checked the physical ID and found it was out of…6Motor Controller Module received an incorrect signal from the pressure sensor.60Motor Controller memory check fault; on power up Motor Controller checked its…61Brown out during Motor Controller EEPROM write; 15-volt supply found below…62Pump over-current fault; excess current detected in pump windings, most likely…63Pump communications fault; Motor Controller detected a problem communicating…64Pressure transducer frequency out of range (<66kHz).65Pressure transducer frequency out of range (>80kHz).66Pressure transducer frequency out of range (>90kHz).7Display Module has found a memory fault.81-95Display to Motor Controller Module communications errors (see fault code 106).9Display size switch setting does not match that stored in memory.

Service modes (13)

  • Data Display (Fault Code Read)["Enter Diagnostic Mode.","Press the SPIN SPEED UP button until the HOLD and SLOW SPIN LEDs are on…
  • Data Display (Fault Code Reading)["Enter Diagnostic Mode.","Press the SPIN SPEED UP button until the HOLD and SLOW SPIN LEDs are on…
  • Diagnostic Mode["Turn the power on at the power point and off at the console.","Ensure machine is not in Stand By…
  • Drain Pump Test["Enter Diagnostic Mode.","Press the REGULAR CYCLE button to turn the drain pump on or off.","The…
  • Fault Code Display (within Diagnostic Mode)["Enter Diagnostic Mode.","Press SPIN SPEED UP button until HOLD and SLOW SPIN LEDs are on (binary…
  • Hot Tub Flag Clear["Enter Diagnostic Mode.","The WATER SAVER LED will be on if spin speed is restricted to 700…
  • Lid Switch & Out of Balance Switch Test["Enter Diagnostic Mode.","Press SPIN SPEED UP button until MEDIUM SPIN LED is on (binary count…
  • Lid Switch & Out of Balance Switch Test (within Diagnostic Mode)["Enter Diagnostic Mode.","Press SPIN SPEED UP button until MEDIUM SPIN LED is on (binary count…
  • Re-Cycle Feature Toggle["Enter Diagnostic Mode.","Press WATER LEVEL UP button to toggle RE-CYCLE on/off.","MEDIUM WATER…
  • Re-Start Feature Toggle["Enter Diagnostic Mode.","Press WATER LEVEL DOWN button to toggle RE-START on/off.","LOW WATER…
  • Recirculating Valve Test["Enter Diagnostic Mode.","Press the Delicate button to turn the recirculating valve on and off."]
  • Size Setting Mode["Turn the power on at the power point and off at the console.","Press and hold the TEMPERATURE UP…
  • Water Valve Test["Enter Diagnostic Mode.","Press WASH TEMPERATURE DOWN to turn Cold Water Valve on (Cold Water LED…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Fisher & Paykel washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass