Model reference
Maytag FAV7500AWW
Washer
4 documents37 error codes20 service modes
Available documentation
Tech Sheet
- Top Load Washer⎯Technical Information13 pg
- Top Load Washer Technical Information14 pg
- Tech Sheet - 16023174_1602317414 pg
Service Manual
- Neptune TL Service Manual98 pg
MyPros+ Max
Diagnose your Maytag FAV7500AWW.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (37)
CodeMeaning
1No Drain10Unbalance or cabinet hit detected during final spin prevented the spinner from…11Will not remember machine settings15Stuck Key16High speed not achieved due to torque17The lid was not opened after the last three completed wash cycles.18Detected lid lock switch open during cycle when not expected (open lid lock…2Lid failed to unlock after multiple attempts.22Detected lid sensor switch open and lid locked switch locked during cycle when…23Lid is locked at start of cycle24Motor high RPM detected two times25Tach signal exists without torque input (abnormal condition)28Water valve thermistor failure3No Fill34Welded system relay4Lid failed to lock after 11 attempts.40Load bound up5Continuous unbalanced loads during spin only; out of balance circuit triggered.6Locked rotor forcing a shut down; rotor is still locked after 10 attempts.8Water level sensor faultCLLid is closed.dcThe load is unbalanced, preventing high speed spin.FLThe machine has repeatedly tried to lock the lid.LEWater level sensor faultLLLarge Load Detected.LOLid has failed to unlockLrLocked RotorndNo DrainnFNo fillodThe lid was not opened after the last three completed cycles.Service modes (20)
- Board Input TestWhile in Service Mode, press the Super Wash key
- Board Output TestWhile in Service Mode, press the Delicates key. Display shows 'ot'. Press
- Clear All Diagnostic CodesWhile diagnostic code is displayed in Service Mode, press Quick Wash + Whites together.
- Cycle Count DisplayWhile in Service Mode
- Diagnostic Code DisplayWhile in Service Mode, press the Wrinkle Control key
- Display Diagnostic CodesEnter Service Mode
- Display Software VersionWhile in Service Mode, press Bulky Items 3 times
- Fast Time Down / Advance to Next StepWhile any test or cycle is running in Service Mode, press the Quick Wash key to advance the program…
- Hold Quick Service Cycle StepPress Signal up and Signal down together to hold at current step.
- Membrane Pad TestWhile in Service Mode, press the Presoak key
- Motor Control Board Output Test1) Disconnect power to washer, 2) Remove front panel and disconnect JP4 connector from Motor…
- Quick Service CycleWhile in Service Mode, press the Wash/Rinse Temp key. Display shows 'sc'. Steps
- Quick Spin TestWhile in Service Mode, press the Hand Wash key to start a Quick Spin Test. Steps
- Service CycleEnter Service Mode, then select Service Cycle option on screen.
- Service ModePress the Enviro Plus and Spin Only keys simultaneously for three seconds or until the control beeps
- System CheckEnter Service Mode, then select the desired output to test on the display
- System Check (Board Output Test)Enter Service Mode, then select System Check on screen
- Tub Displacement Sensor Diagnostic Test1) Enter Service Mode (Enviro Plus + Spin Only for 3 seconds), 2) Press Super Wash key, 3) Press…
- Tub Displacement Sensor Diagnostics1) Enter Service Mode by pressing Help and Back keys for three seconds
- User Interface TestEnter Service Mode, then select User Interface option and follow on-screen directions.
Full entry steps, exit procedures, and test sequences are available in Max.
Related Maytag washer models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax