mypros+
Model reference

Maytag MAH22PDAWW1

Washer

4 documents39 error codes21 service modes

Available documentation

Tech Sheet

  • techsheet-w10240010-reva_W1024001016 pg
    Covers this model
  • Tech Sheet - W10253644 - Rev A (FR)16 pg
    Covers this model

Service Manual

  • Neptune Commercial High Efficiency Washer Service Manual124 pg
    Covers this model

Installation Guide

  • Installation Instructions40 pg
    Covers this model
MyPros+ Max

Diagnose your Maytag MAH22PDAWW1.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (39)

CodeMeaning
d10Door lock sense error or due to power line interference; spins inhibited until…d11Motor speed error detected; cycle paused but can be restarted.d12Tachometer errord13Blocked coin 2 or coin drop control circuit failure; coin recognition and price…d14Pump disconnectedd15Load detected in washer during Washer Cleanout Cycle.d16Not receiving communications from installed debit card reader in Generation 2…d17Door was not locked at the beginning of final spin (MAH21 models).d18Dispenser system errord19Door unlock errord20Communication failure between CCU and MCU.d21Overflow conditiond23Communication failure between CCU and UI.d24Water temperature sensor errord3UI failured4Washer door sense error on control board or due to power line interference…d5Blocked coin 1 or coin drop control circuit failure; coin recognition and price…d6CCU errord7Slow fill detected during previous cycle; maximum fill time or max continuous…d8Last drain was slow (drain time greater than 2 minutes).d9Low voltage detected; less than 90 volts AC for 8 seconds.F01CCU errorF11MCU errorF20No water detected entering washerF21Long drainF22Door lock errorF24Water temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow condition
View all 39 error codes
F28Communication failure between CCU and MCU.F29Door unlock errorF30Dispenser system errorF31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F70Communication failure between CCU and UI (User Interface).F73UI failureF74UI failure

Service modes (21)

  • Code Display Mode["PD Models
  • Cycle Credit["Enter Diagnostic Mode (entire display flashing).","Press the slow key (CC will display)."]
  • Diagnostic Mode["Enter the Setup mode (open service door or turn service key).","Press and hold the Delicates &…
  • Diagnostic Mode (Blink Mode)["First access Setup/Configuration Mode.","Press DELICATES & KNITS button for 1 second while one of…
  • Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the Woolens keypad to start the field…
  • Help Mode["Enter Setup mode.","Navigate to Special Pricing Option mode 2.XX.","Press the Permanent Press…
  • Help Mode (dAS Mode)["Open the service door or insert a manual diagnostic card.","The message dAS will appear in the…
  • Help Mode (PD Models)["Open the service door.","Press the WOOLENS key until display reads 2.XX.","Press the PERMANENT…
  • Manual Overview Test["Enter Flashing Mode (entire display flashing).","Press the WHITES key pad."]
  • Operational Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the WHITES keypad to start the…
  • Quick Drain and Spin["Enter Flashing Mode (entire display flashing).","Press the COLORS key pad."]
  • Quick Overview Test["Enter Flashing Mode (entire display flashing).","Press the WOOLENS key pad."]
  • Quick Spin Cycle (MAH20 Models)["Enter Diagnostic Mode (entire display flashing).","Press the COLORS keypad to start the quick…
  • Relay Test Mode (MAH20PN)["Enter Diagnostic Mode (entire display flashing).","Press the Permanent Press (lower left) keypad…
  • Set-Up Mode (PD Models)["Insert access door key, turn, and lift to remove access door.","Use the lower fabric setting key…
  • Set-Up Mode (PR Models)["Unplug washer or disconnect power.","Open console, disconnect plug on connector AA1, close…
  • Setup / Programming Mode["Insert access door key, turn and lift to remove the access door (PD/PS models).","For PN models
  • Setup/Configuration Mode["PD models
  • Washer Cleaning Program["Enter Diagnostic Mode (Blink Mode).","Press BRIGHT button while the display is blinking."]
  • Washer Cleanout Cycle["Enter Flashing Mode (entire display flashing).","Press the BRIGHT key pad."]
  • Washer Diagnostic Mode (Flashing Mode)["Enter Set-Up Mode first (PD

Full entry steps, exit procedures, and test sequences are available in Max.

Related Maytag washer models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass