mypros+
Error code reference

Bosch Refrigerator Error Code E9000

Compartment temperature sensor 1 open/short

Bosch codesBosch refrigerator codes

Compartment temperature sensor 1 open/short

MyPros+ Max

Get the full diagnostic procedure for E9000.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E9000 means on a Bosch refrigerator

The E9000 error code on a Bosch refrigerator indicates a fault with compartment temperature sensor 1, specifically that the sensor circuit has been detected as either open (broken circuit) or shorted (circuit path collapsed to near-zero resistance). This sensor is a negative temperature coefficient (NTC) thermistor that continuously monitors the internal compartment temperature and sends resistance-based readings to the main control board. When the control board detects resistance values outside the expected operating range, either too high indicating an open circuit or too low indicating a short, it triggers the E9000 code and may impair the refrigerator's ability to regulate cooling properly.

An open circuit condition typically occurs when the thermistor element itself has failed, the wiring harness has developed a break, or a connector has corroded or pulled loose. A short circuit condition usually points to damaged wire insulation causing two conductors to contact each other, or a thermistor that has internally failed with very low resistance. Both fault types prevent the control board from receiving accurate temperature data, which can cause the compressor and fan system to behave erratically or shut down as a protective measure.

Diagnosing this code requires inspecting the wiring harness routing from the sensor to the control board for visible damage, checking connector seating and pin condition, and measuring the thermistor's resistance at a known temperature to confirm whether it falls within the expected NTC curve. If wiring and connectors are intact, the thermistor itself is the most likely failed component and will require replacement.

Source: manufacturer service documentation.

Common causes of E9000

  1. 01

    Failed NTC thermistor

    Part replacement

    The temperature sensor itself has failed internally, producing resistance values that are either too high (open) or too low (short) for the control board to interpret. Measuring the thermistor's resistance with a multimeter will confirm this if readings are out of range or read as infinite or zero.

  2. 02

    Loose or corroded wiring connector

    Wiring / connection

    The connector linking the sensor to the wiring harness may have worked loose or developed corrosion on the pins, interrupting the circuit. Visually inspecting and reseating the connector, or cleaning the pins, can resolve this without replacing parts.

  3. 03

    Damaged wiring harness

    Part replacement

    The wire running from the thermistor to the control board may have a break or damaged insulation, caused by pinching during a previous repair, rodent damage, or repeated flexing. A continuity test along the harness will identify a break or short.

  4. 04

    Control board fault

    Part replacement

    In less common cases, the main control board may misread the sensor circuit due to a failed input circuit on the board itself. This is typically considered only after the sensor and wiring have been confirmed good.

See the test procedure for each cause

Frequently asked questions about E9000

What does E9000 mean on a Bosch refrigerator?
E9000 indicates that compartment temperature sensor 1 has been detected as open or shorted. This means the control board cannot receive a valid temperature reading from that sensor. The fault can originate at the sensor itself, the wiring, or the connector between them.
Can I fix the E9000 error myself?
A knowledgeable DIYer can inspect the wiring harness and connectors for visible damage and reseat any loose connections without special tools. Testing the thermistor requires a multimeter capable of reading resistance. If the thermistor or wiring harness needs replacement, the repair is moderately straightforward but does require disassembling interior panels to access the sensor.
Is it safe to keep using my refrigerator while E9000 is displayed?
Operating the refrigerator with an active E9000 code is not recommended for extended periods. Without accurate temperature feedback, the cooling system may run incorrectly, potentially allowing food to reach unsafe temperatures. Monitor actual compartment temperatures with a separate thermometer if you need to continue using it briefly while awaiting repair.
How much does it cost to repair the E9000 error on a Bosch refrigerator?
Repair costs vary depending on which component has failed. A replacement NTC thermistor typically costs between $15 and $50 for the part. If professional labor is required, total repair costs including diagnosis and installation generally range from $100 to $250 depending on your location and the service provider.
Will resetting the refrigerator clear the E9000 error code?
A power reset may temporarily clear the E9000 code from the display, but the error will return if the underlying fault with the sensor or wiring is still present. Clearing the code without addressing the root cause does not restore proper temperature sensing. A lasting fix requires diagnosing and repairing the sensor circuit.

Related Bosch refrigerator codes

All Bosch refrigerator codes
View all 209 Bosch refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass