mypros+
Error code reference

Electrolux Oven Error Code F102

The oven door is not fully closed or the door lock is defective.

Electrolux codesElectrolux oven codes

The oven door is not fully closed or the door lock is defective.

First step from the service manual

Fully close the door. Deactivate the oven with the house fuse or safety switch in the fuse box and activate it again. If F102 appears again, contact Customer Care.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F102.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F102 means on a Electrolux oven

The F102 error code on an Electrolux oven indicates that the control system has detected the oven door is not fully closed, or that the door lock mechanism has failed to confirm a proper latched position. This code is directly tied to the door lock assembly and its associated position sensor or switch, which communicates door status to the oven's control board. The control board monitors this input continuously and triggers F102 when it does not receive a confirmed closed or locked signal within the expected parameters.

The door lock system typically consists of a motorized latch assembly, a door switch or micro-switch, and wiring connecting these components to the main control board. If the door is physically ajar, the switch will not register a closed state. If the door appears closed but the code persists, the fault is more likely mechanical or electrical in nature, such as a worn latch hook, a failed switch, or a wiring issue between the lock assembly and the control board.

This error is particularly relevant during or after a self-clean cycle, as the door lock is actively engaged during high-temperature cleaning operations. A lock motor that has seized, a latch that has become misaligned due to hinge wear, or a switch that has failed due to heat exposure are all plausible causes when F102 appears in that context. A power cycle by switching off the circuit breaker or fuse can clear a transient fault, but recurring F102 errors point to a component-level problem requiring hands-on inspection.

Source: manufacturer service documentation.

Common causes of F102

  1. 01

    Door not fully closed

    Wiring / connection

    The simplest cause is that the oven door was not pushed completely shut, preventing the latch from engaging. Inspect the door for any obstruction such as a food spill, rack misalignment, or debris along the door gasket.

  2. 02

    Faulty door lock switch or position sensor

    Part replacement

    The micro-switch or sensor inside the door lock assembly may have failed, causing the control board to receive no signal or an incorrect signal even when the door is physically closed. This typically requires replacement of the door lock assembly.

  3. 03

    Worn or misaligned door latch

    Part replacement

    Over time the latch hook or strike plate can wear down or shift, preventing a solid mechanical engagement. Visually inspect the latch for damage, deformation, or misalignment with the strike point on the oven frame.

  4. 04

    Failed door lock motor

    Part replacement

    On models with a motorized latch, the motor that drives the lock mechanism can seize or burn out, especially after repeated self-clean cycles. A non-responsive motor will prevent the latch from confirming a locked position.

  5. 05

    Damaged or loose wiring to the door lock assembly

    Wiring / connection

    Wiring harness connections between the door lock assembly and the control board can loosen or sustain heat damage over time. Inspect the connector pins and wiring for corrosion, fraying, or disconnection.

See the test procedure for each cause

Frequently asked questions about F102

What does F102 mean on a Electrolux oven?
F102 means the oven's control system has detected that the door is not fully closed or that the door lock mechanism is not functioning correctly. The oven monitors the door latch and its associated switch to confirm a secure, closed position. When that confirmation is missing, F102 is triggered to prevent unsafe operation. Firmly closing the door and resetting the oven is the recommended first step.
Can I reset the F102 error on my Electrolux oven myself?
Yes, you can attempt a reset by switching off the oven's circuit breaker or fuse at your home's electrical panel, waiting about 30 seconds, and then restoring power. If the F102 code does not return, the fault was likely a temporary glitch. If the error reappears after the reset, a component such as the door latch or door lock switch will need to be inspected and possibly replaced.
Is it safe to use my Electrolux oven when F102 is displayed?
You should not attempt to operate the oven while F102 is active, particularly if the code appears during or after a self-clean cycle, as the door lock is a safety-critical component during high-temperature operation. Using the oven with a faulty door lock could pose a burn or fire hazard. Resolve the error before resuming normal cooking use.
How much does it cost to fix an F102 error on an Electrolux oven?
If the fix is simply closing the door properly or clearing a physical obstruction, there is no cost involved. If a component such as the door lock assembly, latch, or switch needs replacement, parts alone can range from roughly $30 to $150 depending on the specific model. Adding professional labor typically brings the total repair cost to somewhere in the $100 to $300 range.
Why does F102 keep coming back on my Electrolux oven after I reset it?
A recurring F102 error after a power cycle points to a hardware fault rather than a temporary software glitch. The most likely causes are a failed door lock switch, a worn or misaligned latch, a seized lock motor, or a damaged wiring connection between the lock assembly and the control board. Each of these issues requires a physical inspection to identify and correct the specific failed component.

Related Electrolux oven codes

All Electrolux oven codes
View all 186 Electrolux oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass